Wolf Power WSA105 Owner'S Manual Download Page 6

Be sure to use plug that is properly grounded.
The maximum gradient of the supporting surface for the washing machine should not exceed 2

º

.

Do not tear down electrical wires and components in the machine by yourself.
There are holes on the base for ventilation. These holes  should not be blocked by foreign objects 

    (carpets, etc.).

Never connect the grounding wire with the live wire, or it may lead to an electric shock. 
If the power cord is damaged, it must be replaced by a qualified person to avoid a hazard. 

Do not connect to the hot water supply.





After using, be sure to unplug the power plug.

If the following symptoms occur, please disconnect the power plug and perform the 
following checks:

 After you use the washing machine, never forget to do the following two things:

Attention To  Maintenance

Cabinet  maintenance

Cleaning the lint filter

After using the washing machine,wipe 
the moisture and stain on it with a piece 
of soft cloth.To avoid damage to the 
surface,do not use corrosive or volatile 
chemicals.

Anti-freezing protection

▲ 

To prevent from freezing:

▲ 

If the water is frozen, please take the following steps:

Cabinet

Frame

Press the button head, and

    pull the lint filter out.

Turn the filter net inside out, and rinse it

    in water.

After inserting the claw, press the button 

    to insert it into place. 

A sound of “ba” means proper installation.

Button head

Claw

   hose completely.

Lay the drain hose and turn the drain selector knob to the "Drain”position to  

   empty the water in the tub.

water inlet

Turn off the water tap, remove the water inlet hose and empty water in the 

 

Keep about 2 liters of warm water below 50

 in the wash tub for 

   about 10 minutes. and then lay the drain hose and turn the
   wash drain selector knob to the "Drain”position to empty the water .

Fit the water inlet hose and turn on the water tap to 

   confirm water filling and draining work properly.

Put the water inlet hose into warm water of about 50

.

Operation when objects are

dropped into the outside of the spin tub

Remove all screws on the frame with a screw driver and 

   loosen the connector of the brake belt .

Pull up the frame with both hands and turn it backwards.

Take out the clothes dropped into the outside of the spin tub.

Fasten the connector of the brake belt ,Press the frame to 

    reset and tighten screws.

2. Remove the water inlet hose.

1. Disconnect the power plug.

Check that the power supply is in good condition.
Check that the power plug is inserted properly.

● 
● 
● 

Check that the wash timer knob or the spin timer knob is not 

     in the "0" position.

Check that the drain hose is not laid too high.
Check that the drain hose is not frozen.
Check that the drain hose is not blocked by foreign matter. 

● 
● 
● 

Check that there are no coins or any other foreign objects 

     dropped into the wash tub.

● 

Check that the washing machine is placed on flat, stable floor.
Check that clothes are evenly distributed in the spin tub.
Check that there are no washing materials or foaming debris 

     dropped into the outside of the spin tub.

● 
● 
● 

The washing 
machine does 
not work.

The drain hose 
does not work.

There is abnormal 
noise during washing.

There is abnormal 
noise and violent 
vibration during
spinning.

Symptom

Reason

-9-

-8-

Maintenance

Maintenance

-8-

Notes

The washing machine employs alternative current with rated voltage and frequency . When  voltage fluctuates 
between -10% and 10% of the rated voltage, the machine can work normally.  
Connection mode of the power cord of this machine is Y-shaped connection.Users 
reconnect the wire by themselves.

please contact the designated service center.

should not detach or 

If this part needs to be repaired,

Main Technical Parameters

Capacity (dry Clothes)

Power Supply

Input Power (lower drain)

Input Power (upper drain)

Maximum Time

Water volume

Maximum

 

water

 

pressure

Overall dimension

Net weight

Pump Input Power

Wash

10.0 kg

400W

400W

15 min.     35 min.(soak

 

wash)

HI:77L H:  72L  M:  61L  L:  50L 

Spin

4.6kg

135W

135W

5 min.

/

  0.6Mpa

870x512x962(mm)

                                                        26.5kg

                                                        27kg

30W

220-240V/50Hz

Lower  Drain System

Upper  Drain System

Reviews: