Wohler AMP2-VS User Manual Download Page 1

Page: 1 / 26

Title and Contents

.......................................................................

Introduction .........................................................................................

Section 1: Features, Specs, and Installation

....................

Description and Features ......................................................................

Applications and Specifications ............................................................

Installation ...........................................................................................

Section 2: Operation

.................................................................

Front Panel Features ............................................................................

Rear Panel Features ..............................................................................

Audio Amplifier and Speaker Configuration .........................................

Balance Control Characteristics .............................................................

Section 3: Technical Information

.........................................

General Technical Observations ............................................................

SDI to Analog Converter Module (919068 PCB) ....................................

SDI D/A Gain Calibration Fine Adjustment (919068 PCB) .....................

Level Meter Rear Panel 6-Position DIP Switch Settings .........................

Level Meter Internal 10-Position DIP Switch Settings ............................

Level Meter DIP Switch Locations ........................................................

Level Meter Alternative Scales ..............................................................

Level Meter Phase Correlation Featrure .................................................

AMP2-VS Interconnect Block Diagram .................................................

AMP2-VSA Interconnect Block Diagram ...............................................

AMP2-VS and AMP2-VSA

2U Digital Audio Speaker Monitor

With One SDI Input and Output on BNC,

Four Analog Out From SDI on Phoenix, Four

Analog Inputs on XLR (-VSA Only), Two Selected Analog

Stereo Outs on XLR, Four 53-Segment Level Meters,
Summable Channel Assignment, and Phase Indication

Document P/N

821583

Rev-

CONTENTS

User Manual

ECO-2507 (08/11/04)

Summary of Contents for AMP2-VS






















Search results

Summary of Contents for AMP2-VS

Reviews:

Related manuals for AMP2-VS

Brands by name

Popular brands

Wohler AMP2-VS, User Manual

Search results

Summary of Contents for AMP2-VS

Reviews:

Related manuals for AMP2-VS

Brands by name

Popular brands