background image

25

KEY    PART            
NO.     NO.                DESCRIPTION

KEY    PART            
NO.     NO.                DESCRIPTION

1         73900500       Nut, Flange  5/16-18
2         161415X603  Shield, Side, Outer L. H.
3         8393J             Pin, Stake, Depth
4         12000035       Ring, Klip
5         180847           Bolt, Carriage  5/16-18 x 3/4 
6         8394J             Spring
7         8392J             Bracket, Latch
8         109230X        Spring, Depth Stake
9         102326X603  Shield, Tine
10       72140508       Bolt, Carriage 5/16-18 x 1
11       73220500       Nut, Hex  5/16-18
12       10040500       Washer, Lock  5/16
13       72110510       Bolt, Carriage  5/16-18 x 1-1/4
14       124343X        Bracket, Shield Tine
15       161414X603  Shield, Side, Outer R.H.
16       73900400       Nut, Hex Flange 1/4-20 UNC

18       72040410       Bolt, Carriage  1/4-20 x 1-1/4 Gr. 5
19       102701X        Grip
20       73220600       Nut, Hex  3/8-16
21       102156X        Stake, Depth
22       74930632       Bolt, Hex  3/8-16 x 2
23       4440J             Hinge
24       72140404       Bolt, Carriage  1/4-20 x 1/2 Gr. 5
25       6712J             Cap, Vinyl
26       109227X        Pad, Idler
27       102695X603  Shield, Leveling
28       120588X        Pin, Hinge
29       104085X603  Shield, Side
32       73220400       Nut Fin Hex 1/4-20 UNC
33       10040400       Washer Lock Hvy Helical 1/4

NOTE:

  All component dimensions given in U.S. inches.

 1 inch = 25.4 mm

REPAIR PARTS

TILLER - - MODEL NUMBER WAR500A

TINE SHIELD

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for WAR500A





























Reviews: