manualshive.com logo in svg

Witschi Watch Expert, Operating Instructions Manual

Share
Download
Witschi Watch Expert Operating Instructions Manual Download Page 34

Only perform the following steps if you wish to use

a thermal printer.

Personnel:

n

Operator

Materials:

n

Printer cable

1.

Connect the printer cable to the thermal printer.

2.

Insert the printer cable into the printer port (Fig. 12/1).

ð

The thermal printer is now connected.

Consult the manufacturer’s documentation before

using the thermal printer.

Another possibility is to connect the Watch Expert

to the printer via a Bluetooth connection using a

Bluetooth kit (Type no. 95.1510).

4.6  Switching the Watch Expert on/off

Personnel:

n

Operator

Requirement:

n

The Watch Expert has been commissioned correctly (

Ä

 page

31

).

Switch on the Watch Expert by setting the 

[I/O]

 switch

(Fig. 13/1) to 

[I]

.

ð

The welcome screen is displayed.

If the wrong language is set, set the language

(

Ä

 page 62).

Fig. 12: Printer port

Switching on the Watch Expert

Fig. 13: Switching on the Watch

Expert

 Commissioning the Watch Expert

Switching the Watch Expert on/off

27.02.2018

Precision measuring device Watch ...

34

Summary of Contents for Watch Expert














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands