Wistar RS 005 Instructions Download Page 3

RS 005 Instruction

03

0

RS005 motion sensor function

8

1)When the wind comes up, the awning starts to shake. If the shaking is greater than the set threshold , the awning will 

close automatically. At this time, the remote control is blocked and can not Open/Stop/Close the awning for 30s. 

2)When the wind dies down, the shake is lower than the set threshold. The awning can be opened by the remote 

control after 30s. 

Replace batteries

9

 

Instruction

RS 005

Slide off the upper cover and open the inner cover and replace with 2 pcs of AAA Alkaline batteries. For details, please 

refer to step 4.

10

1

Long press 
for 5s

1

1

1

)

emitter for 5s, the motor will vibrate once.

Press the learning button on the back of 

2

)

Press Down button once.

3

)

motor will vibrate once. De-activate 
of RS005 motion sensor is successful.

Press Stop button to exit, and the 

1

De-activate RS005 motion sensor

11

Problems

Causes

Solutions

The LED does not flash when 
batteries are inserted

Batteries are inserted incorrectly

Check the battery and make sure that 
polarity are installed correctly

The awning does not close when
the wind comes up

Installation direction is incorrect 
(bottom installation and side installation)

If installed in the load bar either at the ends or 
in the middle, switch to the Fron/Back side by 
connecting 1 and 2 position (use the supplied 
connector). If installed at underside of the load 
bar, switch to the Underside side by connecting 
2 and 3 position (use the supplied connector)

Value setting is inappropriate

External wireless signal interfere, or 
signal is blocked by metal objects

Motion sensor or the motor is broken

Reset the value

Check if there are sources of interference 
or metal objects nearby

Shake the awning manually if the awning 
does not retract, replace with new batteries

If the awning still does not retract, 
check if the motion sensor and motor 
works normally

The awning will close every 30 
minutes and the motion sensor LED 
lights flash continuously

The battery voltage is too low
(lower then 2.7 V)

Replace with new batteries

The awning close once per hour

Motion sensor is installed inappropriate

Check if the upper cover and bottom 
cover are connected well

Motion sensor and the motor could 
not work and lose the radio link

The motion sensor does not work

Replace with new battery, shake the 
awning to check if the awning still 
could not retract

Replaced with new battery. If after replacing 
the battery, the awning still retract once per 
hour, then replace motion sensor

Problems and Solutions

12

Delete 

!

  

 

Notes

Setting may fail due to the interference of signal. If in this case, please reset.
Do not install the product where the rain may shower.
Set appropriate threshold, if the threshold set is too low, which will cause a larger power consumption; if the 
threshold set is too high, which will cause the insensitivity. If the battery voltage is low, motion sensor will not 
work, please replace with new battery.
All products are as per material subjects if there is change in appearance, color, function etc. The information is 
subject to changes without prior notice.

1

Note:

There is a time interval of 5 minutes between deactive and active again.

The motion sensor could not 
active successfully

There is a time interval of 5 minutes 
between deactive and active again

wait for 5 minutes and active again

11

.

03

.

03

.

SMS

-

RS005YT-02-V2

A: Delete sensor:

 

not control the motor.

 

All emitters and motion sensor could 

3

)

2

)

motor vibrate. 

Press Up button once and the 

1

)

Press Up and Down button simultaneously, 

and press Down button 6 times.

1

1

6

1

B: Delete all emitters and motion sensors learned:

 

3

Long press  S

1

1) Long press the learnig button on 
the sensor for 3s 

2) the motor vibrates once

3) the sensor cannot control the motor

Reviews: