the fire button or leave the interface for about 10 seconds to confirm. Note: 1. The TCR value in the sheet is 10 5 multiplied of the actual TCR. 2.
The TCR value range is 1-1000. Supplementary TC Modes Functions: Temperature adjustment: In TC modes, the temperature can be adjusted
from (100-315°C or 200-600˚F) with the two regulatory buttons, right to increase and left to decrease.
Shift between °C and ˚F: If you increase the temperature to 315°C, and continue to press the right regulatory button, the temperature readings will
automatically change to the lowest Fahrenheit (200˚F). Equally, if the temperature is decreased below the minimum (100°C), the unit will change
back to ˚F automatically, and the temperature will start to decrease from 600˚F.
Wattage adjustment: While the wattage sign blink, press the right or left regulatory button to adjust the wattage, and press fire button to confirm.
Long pressing the right or left regulatory button will make the wattage setting rapidly increase or decrease.
Resistance locked function: While the resistance sign blink, press the right regulatory button to lock or unlock the resistance of the atomizer. (Note:
Such operation should be carried out at room temperature.)
New atomizer installation: In TC mode, be careful to attach new atomizers that have cooled to room temperature. If a new atomizer has not cooled
down before attaching, the temperature may read and protect incorrectly until the new atomizer cools. Note: 1. When you connect a new atomizer
or disconnect and reconnect your existing atomizer, the device will prompt you to confirm this change and a message will prompt “NEW COIL
RIGHT, SAME COIL LEFT”. Press the right regulatory button to confirm that a new atomizer has been attached. Press the left regulatory button
to confirm that the same atomizer has been reconnected. 2. When using normal coil or the resistance of coil you used is higher than 1.5ohm in TC
modes, the device will automatically switch to VW mode. Shift among Current, Puff and Time: While the user information sign blink, press the right
regulatory button to shift among current, puff and time. The Setting of Preheat Function: (1). When powered on, press the fire button and right
regulatory button simultaneously and then you enter the preheat setting menu. (2). Press the fire button to switch between preheat power and
preheat duration. (3). Press the left or right regulatory button to decrease or increase the parameter. (4). Long press the fire button to confirm.
Adjustable Timeout Duration: Due to different vaping habits, you’re allowed to set the timeout duration from 5 to 15 seconds as you prefer. Press
the fire button and right regulatory button simultaneously to enter into the menu system. Press the right regulatory button to enter the timeout
duration setting. Press the left regulatory button to set the duration and then press the fire button to confirm. Once the duration is set (like 5
seconds), when you hold the fire button and vape over the pre-set time, it’ll display “OVER 5S PROTECT” and shut down automatically. Press
the fire button 5 times to restart. Charging Protection (ENU): While charging, if the temperature of the device is higher than 45℃, it’ll
display“Battery Too Hot”. On the contray, if the temperature is lower than -5℃, it’ll display “Battery Too Cold”. While charging, when the
temperature of the device reaches to 50℃ or higher, the device will stops charging until the temperature drops down to 45℃ or lower.
The Setting of ENU: (1). When powered on, press the fire button and right regulatory button simultaneously and then you enter the menu system.
(2). Press the right regulatory button two times to enter the ENU menu. (3). Press the left regulatory button to shift between “ON” and “OFF”.
(4). Press the fire button to confirm.
How to Reset: If you get stuck while upgrading, just press the right regulatory button and then insert into the reset hole with a needle to restart.
Malfunction Indication and Protection: No Atomizer Alert: When the device does not detect an atomizer, the OLED screen will display “NO
ATOMIZER FOUND” and the indicator light will flash 10 times. Atomizer Low Alert: When the resistance of atomizer is lower than 0.1ohm in
VW mode or lower than 0.05ohm in TC modes, the OLED screen will display “ATOMIZER LOW”.
Atomizer Short-circuit Protection: When atomizer short-circuit occurs, the OLED Screen will display“ATOMIZER SHORT”.
Temperature Alert: If the internal temperature of the device is over 70°C, the output will shut off automatically and the screen will display
“DEVICE TOO HOT”. Temperature Protection: In TC modes, if the actual temperature of coil reaches the set temperature, the device shows
“TEMP PROTECT”.
Weak Battery Alert: In VW/TC mode, when the device installed with an atomizer is working and the voltage of battery is below 2.9V, the device
shows “WEAK BATTERY”. Meanwhile, the output power will be reduced accordingly.
Check USB Alert: When the voltage of the USB charger is equal or greater than 5.8V, the OLED screen will display “CHECK USB ADAPTER”
after inserting the USB cable or vaping.
Charge Error Alert: When no current is detected in charging state, the OLED screen will display “CHARGE ERROR”.
Warranty Please consult with your WISMEC distributors for warranty policy. We are not responsible for any damage caused by user error. This
warranty is only valid for authentic WISMEC products within warranty period from date of purchase by the end user.
Warning 1. Keep out of reach of children. 2. This product is not recommended for use by young people, non-smokers, pregnant or breast-feeding
women, persons who are allergic/sensitive to nicotine. Contra-indication 1. Only have your product repaired by Wismec. Do not attempt to repair
the unit by yourself as damage or personal injury may occur. 2. Do not leave the product in high temperature or damp conditions, as this may
damage the product. The appropriate operation temperature is within 0°C to 45°C while charging and -10°C to 60°C while in use. 3. Keep away
from water. Possible adverse effects 1. Use of this product may cause damage to health. 2. For people with adverse reaction after using this
product, it is recommended to use the juice with lower nicotine content or no nicotine.
Wismec: kostenlose Logos für Akkuträger.
