background image

31

Obtaining Service

We take great pride in our dealers. Experience, dedication, and integrity make 
these professionals ideally suited to assist with our customers’ service needs.

If you develop a problem with your Wisdom Audio subwoofer, please contact 
your dealer. Your dealer will then decide whether the problem can be remedied 
locally, or whether to contact Wisdom Audio for further service information or 
parts. The Wisdom Audio Service Department works closely with your dealer to 
solve your service needs expediently.

 

Important! 

Return authorization must be obtained from Wisdom Audio’s Service 
Department BEFORE a unit is shipped for service.

It is extremely important that information about a problem be explicit and com-
plete. A specific, comprehensive description of the problem helps your dealer 
and the Wisdom Audio Service Department locate and repair the difficulty as 
quickly as possible.

If the drivers in your S90i have been damaged (as, for example, by direct DC 
current being applied from an amplifier that failed), the enclosure is designed 
to provide for servicing in place, without having to uninstall the enclosure. 
Wisdom Audio will work closely with your dealer to resolve the problem.

Summary of Contents for Sage S90i





































Reviews: