background image

ABOUT THIS WATCH

44

Features

This is a solar radio-controlled watch.  The watch receives official standard frequencies of Japan (from either of two transmitting stations) to 
display correct time. A solar cell underneath the dial converts any form of light into"electrical energy"to operate the watch.

This watch is equipped with the following functions in addition to the time (hour and minute) display.

■Automatic Time Setting ・

  →  P.55

■Display of Radio Signal Reception Level ・

  →  P.58
■Display of Radio Signal Reception Result ・

  →  P.61

■Solar Rechargeable Battery・

  →  P.48
■Display of Remaining Battery Amount・

  →  P.50
■Power Save ・

  →  P.52

The  watch  maintains  the  accurate  time  by 
automatically  receiving  radio  signals  on  the  official 
standard frequency of Japan.  It is also possible to 
make the watch manually receive radio signals.
During  reception  attempts,  the  watch  displays  the 
strength of radio wave signals.
The latest reception result (success/failure) and the 
date  and  time  for  which  the  latest  reception  was 
successfully performed can be confirmed.
Once fully charged, the watch continues to run for 
approximately 3 months.
The  approximate  amount  of  energy  stored  in  the 
watch's battery can be displayed.
The Power Save mode can be activated in order to 
reduce  unnecessary  energy  consumption  when  the 
watch is left without an adequate light source.

■Automatic calendar ・

  

■World Time ・

  →  P.62
■Single-Time Alarm Function ・

  →  P.64
■Daily Alarm Function ・

  →  P.65
■Stopwatch ・

  →  P.66

■Timer ・

  →  P.67

The calendar automatically adjusts for odd and even 
months including February of leap years from January 
1, 2006 to December 31, 2099.
The watch displays the time for 32 cities and regions 
all over the world.
An alarm that sounds only one time at the set time 
can be set.
An alarm that sounds everyday at the set time can be 
set.


Time can be measured in 1/100 sec increments.
The maximum measurement time is 9 hours 59 min 
59. 99 sec.
The countdown timer can be set from 1 min to 9 hours 
59 min by the minute.

Summary of Contents for W36 Series

















































































Reviews: