Winterthur Gas & Diesel Ltd. X52 Operation Manual Download | Manualshive

Page: 202 / 519

background image

5.9.3

Oil mist detector

The oil mist detection system continuously monitors the concentration of oil mist in the crankcase,
in the supply unit drive and in the supply unit. If there is a high oil mist concentration, the oil mist
detector activates an alarm. Thus damage to the bearings can be quickly found and explosions in
the crankcase can be prevented.

The system includes the sensors (002,

) and the control unit (003) on the engine.

Fig 5-50

Oil mist detector (example)

004

003

001

002

Legend

001

Data cable

003

Control unit E15.1

002

Sensor

004

Column

Each sensor monitors the concentration of oil mist. Each sensor has a self-test function to make
sure that there are no internal faults.

X52

AA00-9314-00AAA-043A-A

Operation Manual

Oil mist detector

Winterthur Gas & Diesel Ltd.

- 202 -

Issue 002 2018-11

«
...
200
201
202
203
204
...
»

Summary of Contents for X52








































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X52

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

MET ONE 3400 Series

Brand: Hach Pages: 48

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Pages: 12

Brand: Hanil Pages: 24

Brand: Hanil Pages: 32

Brand: Hanil Pages: 24

Brand: unios Pages: 2

Brand: York Pages: 16

i.Profiler plus

Brand: Zeiss Pages: 66

Brand: Yetter Pages: 24

Brand: Wayflex Pages: 11

Brand: ABB Pages: 106

FUSION Equine DR II

Brand: SOUND Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands