manualshive.com logo in svg

Winterthur Gas & Diesel Ltd. X52, Operation Manual

The MSI X52 Quick Installation Manual is a comprehensive user guide designed to assist you in setting up and utilizing your MSI X52 product efficiently. This manual is available for free download on our website, ensuring easy access and enabling you to get started quickly.

Share
Download
background image

5.5.5

Flow limiting valve

For each cylinder there is one flow limiting valve installed on the fuel rail.

The position of the piston (003, 

Figure 5-32

) gives the quantity of fuel for the injection. When the

injection valves open, the piston (003) moves to the right until the injection stops. When the
injection valves are closed, the piston (003) moves back to the start position.

If the injection time is too long (eg if an injection valve is stuck open), the piston (003) closes the
supply.

If an injection valve is damaged, the flow limiting valve sets the maximum limit of fuel that can be
injected into the cylinder.

Fig 5-32

 Flow limiting valve (generic)

Legend

001

Fuel outlet

003

Piston

002

Fuel inlet

X52

AA00-5565-00AAA-043A-A

Operation Manual

Flow limiting valve

Winterthur Gas & Diesel Ltd.

- 170 -

Issue 002  2018-11

Summary of Contents for X52








































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X52

Taylor 490 Operator Training preview
490
Brand: Taylor Pages: 70
Raith 150 System Operation Manual preview
150
Brand: Raith Pages: 26
Kane 501C Manual preview
501C
Brand: Kane Pages: 16
FJC 45135 User Manual preview
45135
Brand: FJC Pages: 2
OceanSat AIS Manual preview
AIS
Brand: OceanSat Pages: 85
Nautilus F3 0-90 Manual preview
F3 0-90
Brand: Nautilus Pages: 17
National Instruments PXIe-8240 Getting Started Manual preview
PXIe-8240
Brand: National Instruments Pages: 6
Safavieh TBL4102 Quick Start Manual preview
TBL4102
Brand: Safavieh Pages: 2
Vendlet STANDARD Quick Manual preview
STANDARD
Brand: Vendlet Pages: 2
Kärcher SP 16.000 Dirt Manual preview
SP 16.000 Dirt
Brand: Kärcher Pages: 148
GE Venue 50 Basic Service Manual preview
Venue 50
Brand: GE Pages: 289
CAB PX Q4.3L Service Manual preview
PX Q4.3L
Brand: CAB Pages: 30
Hameg HM 8122 User Manual preview
HM 8122
Brand: Hameg Pages: 39
Teac CD-RW890 Specifications preview
CD-RW890
Brand: Teac Pages: 1
Garelick 31800 Assembly Instructions preview
31800
Brand: Garelick Pages: 2
HOMCOM A91-080 Assembly Instruction Manual preview
A91-080
Brand: HOMCOM Pages: 11
Seto Powerator 1800 compact Instructions For Use Manual preview
Powerator 1800 compact
Brand: Seto Pages: 39
Veeder-Root VaporTEK Installation, Setup And Troubleshooting Manual preview
VaporTEK
Brand: Veeder-Root Pages: 58

Brands by name

Popular brands

Load more brands