manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 708

13.2

Hydraulic pipe exhaust valve

13.2.1

Hydraulic pipe exhaust valve - remove

Periodicity

Description

Unscheduled
Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

1.5 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

AR

Support equipment

Description

Part No.

CSN

QTY

None

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Always put on gloves and safety goggles when you do work on hot components. When
drain screws and plugs are opened, servo oil can come out as a spray and cause injury.

CAUTION

Injury Hazard: Use approved equipment or sufficient personnel to lift and move the
hydraulic pipe.

CAUTION

Damage Hazard: Make sure that you do not cause damage the sealing faces or the
hydraulic pipes.

PRELIMINARY OPERATIONS

•

The engine must be stopped and made safe for maintenance, refer to section 

4.1 Do

maintenance work - general procedure

X82-B

AA00-8460-00AAA-520A-A

Maintenance Manual

Hydraulic pipe exhaust valve - remove

Winterthur Gas & Diesel Ltd.

- 708 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands