WinGD X82-B Maintenance Manual Download Page 669

Page: 669 / 841

Fig 11-23 Water separator - view 3

001

002

003

004

005

006

00447

Operate the lever chain hoist (001,

Figure 11-23

) until you can see the bores in the

middle of the top side of the water separator.

Install the lifting tool (002).

Attach the shackles (004 and 005) and the spur-geared chain blocks (003 and 006) to
the lugs of the platform at the exhaust side.

Put the spur-geared chain block (003) into the last hole of the lifting tool (002).

Operate the spur-geared chain block (003) to get sufficient tension to hold the water
separator.

X82-B

AA00-6708-00AAA-520A-A

Maintenance Manual

Water separator - remove

Winterthur Gas & Diesel Ltd.

- 669 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands