manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 639

PROCEDURE

1

Remove the screws (010, 

Figure 11-4

) and the tab washers (011).

2

Remove the two flat bars (002, 003) and the stop plate (009).

3

Remove the screw (008) and the tab washer (007).

4

Remove the guide (006), distance ring (005), shaft (004), and the flap (001).

Fig 11-4

 Flaps - remove

I

00536

001

I

II

II

001

003

005

008

009

011

002

010

007

004

006

CLOSE UP

•

None

X82-B

AA00-6420-00AAA-520A-A

Maintenance Manual

Scavenge air receiver - remove the flaps

Winterthur Gas & Diesel Ltd.

- 639 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands