manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 374

23.2

Put on the applicable personal protective equipment.

23.3

Operate the chain block (002) to lower the connecting rod (001) to the floor.

23.4

Remove the chain.

23.5

Attach the two chain blocks (002 and 006, 

Figure 8-21

) to the connecting rod

(003) and the shackles (005).

23.6

Lift the connecting rod (003) a small distance.

23.7

Attach two more shackles (009) to the top platform.

23.8

Attach two more chain blocks (007, 008) to the connecting rod (003) and
shackles (009) as shown in step B.

23.9

Operate carefully the chain blocks (002, 006, 007, 008) to move the connecting
rod.

23.10

Attach and remove the chain blocks (002, 006, 007, 008) and shackles (005,
009) as given in 

Step 23.9

 to continue to move the connecting rod a sufficient

distance (step C).

23.11

Lower the connecting rod (003) to the floor.

23.12

Attach the engine room crane to the connecting rod (003).

23.13

Remove the chain blocks (002, 006, 007, 008) and shackles (005, 009).

23.14

Operate the engine room crane to lift and move the connecting rod to an
applicable area, for example into storage.

X82-B

AA00-3303-00AAA-520A-A

Maintenance Manual

Connecting rod - remove

Winterthur Gas & Diesel Ltd.

- 374 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands