WinGD X82-B Maintenance Manual Download Page 237

Page: 237 / 841

PROCEDURE

Remove the piston rod gland together with the piston, refer to the related procedure.

Remove and discard the two O-rings (002,

Figure 7-17

Remove the four screws and nuts (003, 006).

Push the two parts of the housing (001, 005) away from the piston rod.

Remove the two parts of the housing (001, 005).

Fig 7-17

Piston rod gland - remove and install

Remove the parts that follow:

•

Tension springs (002 and 005,

Figure 7-18

)

•

Scraper rings (001, 007)

•

Gaskets (003, 004)

•

Ring supports (006).

X82-B

AA00-2303-00AAA-520A-A

Maintenance Manual

Piston rod gland - remove

Winterthur Gas & Diesel Ltd.

- 237 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands