WinGD X72-B Operation Manual Download Page 490

Page: 490 / 526

Tab 11-7

Oil systems (XX2NNN, part 1)

Description

Usual oper-
ation (value

or range)

Safeguard setting

Medium / physical value / location

Signal number Func-

tion

Le-

vel

Trigger

value

De-

lay

Lubricating oil supply - system side

Main lubricating oil / pressure [bar] / engine
inlet connection 25

4.2 to 5

PT2001A

ALM

≤

4.0

SLD

≤

3.8

PS2002S

SHD

≤

3.3

Main lubricating oil / temperature [°C] / en-
gine inlet connection 25

45 +/-2

45 +/-4

TE2011A

ALM

≥

SLD

≥

External crosshead bearing oil / pressure
[bar] / engine inlet connection 30

10.2 to 13

PT2021A

ALM

≤

10.0

SLD

≤

9.0

Injector lubricating oil

Injector lubricating oil / pressure [bar] / inlet
injectors

4.2 to 5

PT2003A

ALM

≤

2.6

Bearing oil

Main bearing oil / temperature [°C] / outlet
each main bearing (optional)

45 to 60

TE2101-nnA

ALM

≥

SLD

≥

Crank bearing oil / temperature [°C] / outlet
each crank bearing (optional)

45 to 60

TE2201-nnA

ALM

≥

SLD

≥

Crosshead bearing oil / temperature [°C] /
outlet each crosshead bearing (optional)

45 to 60

TE2301-nnA

ALM

≥

SLD

≥

This value is applicable for stable operation condition.

This value is applicable for transient operation condition.

The trigger value is only applicable above 40% engine load.

The trigger value is not applicable when the engine has stopped.

X72-B

AA00-0000-00AAA-033B-A

Operation Manual

List of usual values and safeguard settings

Winterthur Gas & Diesel Ltd.

- 490 -

Issue 003 2021-12

Summary of Contents for X72-B















































































































































































































































































































































































































































































































































Search results

Summary of Contents for X72-B

Reviews:

Brands by name

Popular brands

WinGD X72-B, Operation Manual

Search results

Summary of Contents for X72-B

Reviews:

Brands by name

Popular brands