manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

The WinGD X62DF maintenance manual is available for download for free on our website. This comprehensive manual provides all the information needed to properly care for and maintain your engine. Download it now from manualshive.com to ensure long-lasting performance of your WinGD X62DF engine.

Share
Download
background image

PROCEDURE

1

To set the shut-off valve for starting air (shut-off valve) to the initial test position, do 

Step

1.1

 to 

Step 1.3

:

1.1

Make sure that the stop valves 930-V03 and 930-V04 are closed.

1.2

Use the hand-wheel (001, 

Figure 9-5

) to move the shut-off valve in the position

CLOSED.

1.3

Make sure that the turning gear is disengaged.

2

To do a test the shut-off valve, do 

Step 2.1

 to 

Step 2.8

:

2.1

Close the drain valves 30-8605_E0_6/7 on the supply pipe.

2.2

Slowly open the stop valves 930-V03 and 930-V04.

2.3

NOTE:

If air flows out, tighten the screw plug (011). The shut off valve is not
airtight.

Slowly loosen the screw plug (011). Make sure that no air flows out.

2.4

Remove the screw plug (011).

2.5

Slowly turn the hand-wheel (001) to move the shut-off valve to the position
OPEN.

2.6

Make sure that air flows from the bore of the screw plug (011). When air flows,
the manual function of the shut-off valve operates correctly.

2.7

Use the hand-wheel (001) to move the shut-off valve to the position AUTOMAT.
Make sure that the lever (002) engages with the groove in the spindle.

2.8

Make sure that no air flows from the bore of the screw plug (011). When no air
flows, the automatic function of the shut-off valves operates correctly.

3

To set the starting air shut-off valve into automatic mode, do 

Step 3.1

 to 

Step 3.5

:

3.1

Make sure that the shut-off valve is in the position AUTOMAT.

3.2

NOTE:

When you do the step below, air will flow through the pipe. This
activates the control valve (012), which shows that the valve body and
valve operate.

Open the ball valve 35-8353_E0_2 to activate the control valve (012). The
shutoff valve opens automatically.

3.3

Make sure that air flows from the bore of the screw plug (011).

3.4

Close the ball valve 35-8353_E0_2.

3.5

Make sure that no air flows from the bore of the screw plug (011).

4

To complete the test procedure, do 

Step 4.1

 to 

Step 4.3

:

4.1

Use the hand-wheel (001) to move the shut-off valve to the position CLOSED.

4.2

Install the screw plug (011).

4.3

Attach the pipes (004, 007) to the shut-off valve.

X72DF

AA00-4325-00AAA-320A-A

Maintenance Manual

Shut-off valve for starting air - do a test of the operation

Winterthur Gas & Diesel Ltd.

- 527 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X62DF

Ofna Racing HYPER.21 Quick Start Manual preview
HYPER.21
Brand: Ofna Racing Pages: 2
Plettenberg HP 370 Operating Manual preview
HP 370
Brand: Plettenberg Pages: 26
brel-motors MS55-60 Manual preview
MS55-60
Brand: brel-motors Pages: 2
Lenze M Series Mounting Instructions preview
M Series
Brand: Lenze Pages: 36
Lenze MCA10I40 Series Mounting And Switch-On Instructions preview
MCA10I40 Series
Brand: Lenze Pages: 44
Lenze Smart Motor m300 Mounting Instructions preview
Smart Motor m300
Brand: Lenze Pages: 116
Lenze g350-B Series Project Planning preview
g350-B Series
Brand: Lenze Pages: 72
YS FZ63S Operator'S Manual preview
FZ63S
Brand: YS Pages: 2
Yanmar 2TM Service Manual preview
2TM
Brand: Yanmar Pages: 182
NANOTEC PD4-E Technical Manual preview
PD4-E
Brand: NANOTEC Pages: 295
Baumuller DA 100 Commissioning And Maintenance Instructions preview
DA 100
Brand: Baumuller Pages: 25
O.S. Speed B21 ADAM DRAKE EDITION Instruction Manual preview
B21 ADAM DRAKE EDITION
Brand: O.S. Speed Pages: 4
YAMADA DZ185cdi Operator'S Manual preview
DZ185cdi
Brand: YAMADA Pages: 2
WilTec LIFAN 92453 User Manual preview
LIFAN 92453
Brand: WilTec Pages: 16
Honda GS160 Owner'S Manual preview
GS160
Brand: Honda Pages: 48
DLE 55 User Manual preview
55
Brand: DLE Pages: 4
DLE DLE130 User Manual preview
DLE130
Brand: DLE Pages: 5
Vauth-Sagel HSA power move Operating And Installation Manual preview
HSA power move
Brand: Vauth-Sagel Pages: 14

Brands by name

Popular brands

Load more brands