manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

The WinGD X62DF maintenance manual is available for download for free on our website. This comprehensive manual provides all the information needed to properly care for and maintain your engine. Download it now from manualshive.com to ensure long-lasting performance of your WinGD X62DF engine.

Share
Download
background image

PROCEDURE

1

If necessary, operate the turning gear to move the piston to BDC.

2

If the depth of the lubricating grooves (001, 

Figure 7-8

) has decreased to less than

1.5 mm, do as follows:

CAUTION

When you remove sharp edges, make sure that you keep the initial shape
of the lubricating grooves.

2.1

Use an oil stone or an emery cloth to get the lubricating grooves back to their
initial depth.

3

Fully clean the lubricating grooves and the bore of the cylinder liner.

4

Remove unwanted particles.

5

Manually operate the cylinder lubrication to flush unwanted material from the cylinder
liner.

Fig 7-8

 Lubricating grooves - grind

CLOSE UP

•

None

X72DF

AA00-2124-00AAA-655B-A

Maintenance Manual

Cylinder liner - grind the lubricating groove

Winterthur Gas & Diesel Ltd.

- 185 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X62DF

Jiecang JCC50STEW User Manual preview
JCC50STEW
Brand: Jiecang Pages: 2
Master WIND-P Instruction Manual preview
WIND-P
Brand: Master Pages: 2
Bosch Rexroth ML3 Operating Instructions Manual preview
Rexroth ML3
Brand: Bosch Pages: 106
Bosch rexroth MSK 030 Operating Instructions Manual preview
rexroth MSK 030
Brand: Bosch Pages: 72
Bosch Rexroth MKE Series Project Planning Manual preview
Rexroth MKE Series
Brand: Bosch Pages: 134
Bosch REXROTH MS2E Operating Instructions Manual preview
REXROTH MS2E
Brand: Bosch Pages: 82
Bosch Rexroth MS2N Operating Instructions Manual preview
Rexroth MS2N
Brand: Bosch Pages: 124
Bosch Rexroth MKE E Series Project Planning Manual preview
Rexroth MKE E Series
Brand: Bosch Pages: 138
Pride Mobility Quantum Jazzy 1400 Assembly Instructions preview
Quantum Jazzy 1400
Brand: Pride Mobility Pages: 2
Price Industries Limited ECM Series Troubleshooting Manual preview
ECM Series
Brand: Price Industries Limited Pages: 17
Moons' Applied Motion Products TSM23XIP Quick Setup Manual preview
Applied Motion Products TSM23XIP
Brand: Moons' Pages: 2
Becker L120/11C PSF Assembly And Operating Instructions Manual preview
L120/11C PSF
Brand: Becker Pages: 24
ARRI cforce plus User Manual preview
cforce plus
Brand: ARRI Pages: 28
Lycoming TEO-540-C1A Maintenance Manual preview
TEO-540-C1A
Brand: Lycoming Pages: 568
Hacker SKALAR SC Series Manual preview
SKALAR SC Series
Brand: Hacker Pages: 2
Detroit Diesel 60 Service Manual preview
60
Brand: Detroit Diesel Pages: 22
Kärcher G200FA User Manual preview
G200FA
Brand: Kärcher Pages: 116
DLE DLE61 User Manual preview
DLE61
Brand: DLE Pages: 4

Brands by name

Popular brands

Load more brands