background image

Cutting the Directional Handle to fit Roof Thickness

Carefully align the keys inside 
the directional handle with the 
keyways on the bottom of the 
gear housing. (The keys only line 
up one way—do not force.)

Pull the handle down, and transfer 
this dimension to the shaft end of 
the directional handle. Mark this, 
and cut the handle at the mark.

Push the directional handle up 
into ceiling and over the shaft. 

Measure the distance between 
the bottom of the recess on the 
handle to the ceiling.

Inside the vehicle, mark the 
elevating shaft 3.8 cm below the 
ceiling. Cut the shaft on this mark. 

Make sure the top of the 
directional handle is snug against 
the bottom of the base plate.

Determine the roof thickness. The mount is designed to fit roofs from 2.5 cm to 12 cm thick. 

• 

If the roof is less than or equal to 12 cm thick, continue to step 2.

• 

If the roof is more than 12 cm thick (max. 17.8 cm), a directional handle extension is needed. 
Winegard recommends model EK-1036 directional handle extension (sold separately).

Do not 
connect high

current devices 
such as hair dryers 
to this receptacle. 
Maximum 
current rating of 
receptacle is 8 
amps at +12 VDC.

The power supply may be flush mounted in most standard electrical boxes. To flush mount, cut a hole in the wall to fit the 
box. Run two #12 wires between the wall plate and +12 VDC source, and route downlead cable to this location.

Select a location for the power supply.

Make 12 volt connection to the power supply. Install terminals on wires from +12 VDC source, and crimp the terminals 
with an appropriate crimping tool. If in doubt as to the polarity of the wires, connect them temporarily to the tabs, and 
press the “ON” switch on front of wall plate; if light comes on, polarity is correct. Turn power off.

Installing the Crank Assembly

Lay the ceiling plate on top of

the directional handle with

the pointers aligned. 

Slide the ceiling plate and 
directional handle assembly over 
the rotating base shaft.

Installing the Crank Assembly, Cont.

1

2

Make pilot holes in the ceiling. 
Then, mount the ceiling plate with 
the four provided screws.

3

TIP

 

The knobs on the 
directional handle 

should fit into the grooves 
on the ceiling plate.

Slide the elevating crank (with 
nylon bearing on top) onto the 
rotating base shaft. 

Check that the set screw lines up 
with one of the flat sides of the 
rotating base shaft.

7

8

Tighten the set screw until it 
touches the rotating base shaft. 

Then, tighten only ¼ turn more

.

9

NOTE

 

The set screw simply holds the elevating 
crank to the rotating base shaft.

Installing the Power Supply

1

2

2

3

4

5

6

7

TIP

 

The pointer on the handle should point 
toward the back of the coach.

The handle cut 
must be flat.

1

The power 
supply

should be turned off 
when connecting 
cables/wires.

5                                                                                             Winegard Sensar HV Antenna

Winegard Sensar HV Antenna                                                                                             6

Front of Power Supply

Back of Power Supply

Pointers

3

4

6

2

5

5

7

Set 

screw

Thick key

3.8 cm 
below ceiling

Cut shaft here

distance x

Cut handle here

distance x

EK-1036

Sold Separately

Remove the backing from the 
decal, and place the decal on 
the bottom of the directional 
handle.

Slide the spring over the rotating 
base shaft.

4

5

Place the nylon bearing over the 
top of the crank.

6

Thin key

Directional 

handle

Summary of Contents for Sensar HV










Reviews: