Windster WS-58 series Operation Manual Download Page 2

Table of Contents

Important Safety Instructions

----------------------------

Safety Notes ------------------------------------------------------

Tools and Materials Required ----------------------------------

Accessory Package --------------------------------------------

Preparing the Range Hood

-----------------------------------

Preparing the Installation Location --------------------------

Providing Electrical Power -------------------------------------

Mounting Range Hood to Cabinet ----------------------------

Mounting Range Hood Without Cabinet ---------------------

Making The Electrical Connection -----------------------------

Use and Care ------------------------------------------------------

Maintenance Instruction -----------------------------------------

Ducting --------------------------------------------------------------

Troubleshootings --------------------------------------------------

Parts Layout Diagram ---------------------------------------------

Circuit Diagram ----------------------------------------------------

Size-------------------------------------------------------------------

Replace The LED Light -------------------------------------------

P.1

P.3

P.4

P.4

P.5

P.6

P.7

P.8

P.8

P.9

P.10

P.10

P.12

P.13

P.13

P.14

P.16

P.17

A.

B.

C.

D.

E.

F.

G.

H.

I.

J

K.

L.

M.

N.

P.

Q.

R.

S.

for installation, cleaning, light bulb changing and

dismantling to reduce the risk of any bodily injuries.

Due to sharp edge, please wear

Safety Workman Gloves"

"

Safety Workman Gloves

WARNING

Summary of Contents for WS-58 series






















Reviews: