MACHINE PREPARATION
BATTERIES
1.
Install the
batteries
and
connect
the
cables
as
shown.
PROPER VENTILATION, LEAVE
DOOR
OPEN WHEN
2.
Charge the batteries before using the machine. (See
battery charging procedure).
PAD ASSEMBLY
1.
2.
3.
Turn
OFF
main
power
switch
brush motor
switch
Raise scrub deck assembly
by
raising control lever to
position.
Reach under scrub deck
and
rotate drive plate until a
lug hole is visible through the
deck sight hole.
Splash
NOTE:
Turn
the
Brush Pad
counter
to
lock
securely.
4.
Position
driver under plate and
lift
up
to
engage brush lugs in plate. A quick
motion will lock
driver in position.
Lower scrub deck by pulling control lever rearward.
Adjust splash
to floor.
5.
CLEANING SOLUTION
1.
machine with hot water
and
add cleaning chemical
at the proportion noted
on
the
container.
use a
for use in automatic hard surface floor scrubbers.
To
avoid possible
distortion
of polyethylene
solution/ recovery
tanks.
DO NOT
USE
EXCEEDS
150°F
(65
CHEMICALS
The
parts of
the
pump used
in the
scrubber
(on
models equipped with
pump)
are
suitable for use
with most cleaning chemicals. But it is susceptible to
chemical attach from some cleaning substances, such
as
solvents and chlorinated bleaches. These
compatible materials are not of the type normally used for
cleaning.
S
UITABLE
CHE
MI
CALS
Soaps
Clorox Bleach*
Defoaming Agents
Detergents
White
Monday Bleach*
Hydroxides
D-Limonene
Oxygen Bleaches
Fabric
Wben properly diluted
'Registered Trademark
NONCOMPATIBLE CHEMICALS
Aldehydes
Chlorinated
Aromatic Hydrocarbons
SP
Carbon
Perchorethylene
Phenolics
Chlorinated
Bleaches
Trichlorethylene
Methyl Ethel Ketone (MEK
I
I
C
NOTE:
In
the following instructions
all
letter
designations,
IE:
w i l l
be shown
in
the
coming
graphical examples
in
this
guide.
OPERATING THE MACHINE
1.
Adjust
the
operator control handle to a comfortable
position.
2.
Switch
on
main
power
switch.
3.
Release solution.
(Pull
solution control lever rear-
ward.)
NOTE:
The amount of solution can be regulated
during operation depending
on
the type of floor
and
the
tra-
verse speed
of
the machine.
4.
5.
Switch
on
vacuum motor.
6.
Switch
on
brush drive motor.
Lower scrub deck.
deck lift lever rearward.
CAUTION:
Do not leave brush running
on
floor
while machine
is stationary.
Lower squeegee. Pull squeegee
lift
lever rearward.
NOTE:
Use adjusting knob
to
change pressure
on
the squeegee. Item
26
page
12
of
this manual.
Turn
to page 3 for description
on
Traction Drive
Operation
for the proper
motion
control of the
machine.
CAUTION:
Move control handles slow at
until you
are
comfortable with operation.
7.
8.
4
Summary of Contents for C20X
