Wincor Nixdorf TH210 Programmer'S Manual Download Page 6 | Manualshive

Page: 6 / 152

background image

TH210

Programmer’s Guide

2

Diagnostics and Configuration

The printer performs a number of diagnostics that provide useful information about the operating
status of the printer. The following diagnostic tests are available.



Start-up diagnostics

Perform during the printer’s start-up cycle.



Runtime diagnostics

Perform during normal printer operation.



Remote diagnostics

Maintained during normal operation and reported in the print test.



The printer can be configured with the following settings and functions through the

configuration menu that is printed on the receipt. For more information on
configuring the printer, see “Printer configuration” on page xx.

Communication interfaces

Diagnostic modes

Printer emulations/software options

Hardware options

Firmware features

Start-up Diagnostics

When the printer receives power or performs a hardware reset, it automatically performs the
startup diagnostics (also known as level 0 diagnostics) during the start-up cycle. The following
diagnostics are performed:



Turn off motors



Perform boot CRC check of the firmware ROM and test main program CRC



Failure causes Start-up Diagnostics to stop; the printer beeps and the LED flashes a

set number of times, indicating the nature of the failure. The table in the
“Indicators” section (page 14) describes the specific tone and LED sequences.



Check if paper is present



Return the knife to the home position



Failure causes a fault condition. The table in the “Indicators” section (page 14)

describes the specific tone and LED sequences.



Check if receipt cover is closed



Failure does not interrupt the start-up cycle.

At power up, if the LED blinks twice, every four seconds, the object storage areas are being
initialized. This process could take up to two minutes. Once the object storage area initialization is
complete the printer will continue with its normal startup procedure and operation. DO NOT
RESET THE PRINTER UNTIL THIS PROCESS IS COMPLETE.
When the start-up diagnostics are complete, the printer makes a two-tone beep (low then high
frequency), the paper feed button is enabled, and the printer is ready for normal operation.

«
...
4
5
6
7
8
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: CAB Pages: 263

Brand: Olivetti Pages: 39

Brand: Labau Pages: 19

Brand: Oki Pages: 36

Brand: Oki Pages: 3

Brand: Oki Pages: 147

Brand: Oki Pages: 12

Brand: Oki Pages: 297

Brand: Oki Pages: 111

Brand: Oki Pages: 6

Brand: Oki Pages: 2

Brand: Oki Pages: 108

C5800Ldn Series

Brand: Oki Pages: 266

C5800Ldn Series

Brand: Oki Pages: 276

Brand: Oki Pages: 121

Brand: Oki Pages: 12

Brand: Oki Pages: 354

Brand: Oki Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands