Wincor Nixdorf BEETLE Installation Manual Download Page 14 | Manualshive

Page: 14 / 60

Wincor Nixdorf BEETLE Installation Manual Download Page 14

Planning the Installation

8 BEETLE /FUSION – Installation Guide 01750166737 E

Important safety precautions

Please read the following notes carefully before doing any work on
the device.

Installation notes

-

When installing the device and/or doing any work on it, make sure
that it is disconnected from the power.

General safety precautions

This device complies with the relevant safety regulations for information
processing equipment.

-

Note the warning and information labels on the device.

-

The device is equipped with a safety-tested power cable, which
must be connected only to a grounded outlet.

-

Always hold the plug when removing the power cable. Never pull
the cable itself.

-

Have damaged power cables replaced immediately.

-

The lithium battery must be disposed of in accordance with local
regulations for special waste.

-

If  the  display  element  is  damaged  and  the  liquid  crystal  solution
leaks  out  onto  your  hands  or  clothing,  please  wash  your  hands  or
clothing  immediately  under  running  water  for  at  least  15  minutes,
using  soap  or  alcohol.  If  the  liquid  comes  into  contact  with  your
eyes, consult a medical doctor immediately.

!

«
...
12
13
14
15
16
...
»

Summary of Contents for BEETLE





























































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands