background image

  

© by WilTec Wildanger Technik GmbH  

 

Seite 2  

http://www.wiltec.info  

 

Introduction 

 
Thank you for purchasing this quality product.

 To minimize the risk of injury we urge that our cli-

ents  take  some  basic  safety  precautions  when  using  this  device.  Please  read  the  operation 
instructions carefully and make sure you have understood its content.

 

 

 

Attention   

The wall has to carry at least 37 kg for 23-37“ (33-94 cm) devices. If this is not the case, the wall has 
to be reinforced. The installation has to be carried out by a pro. Errors can lead to severe injuries or 
death. 
 

Attention 

 

You must comply with the safety regulations. Use suitable tools to avoid injuries. 
 

Attention 

 

 

Before installing the TV-wall mount bracket you have to read and understand this manual guide in 
order to avoid personal injury and property damage. Keep the manual guide in a safe place in case 
you need it in the future. 
  
 
              
                 The wall has to be stable enough to carry the weight of the TV. Install your TV-mount 
bracket on dry walls, on previously determined studs or mounting rails or with special rawl plugs. 
 

 

 
 

Do not mount it on vibrating, moving walls or on walls exposed to shocks. This could dam-

age your TV or the mounting surface. 
 
 
 

Do not mount it near heating elements, fireplaces, air conditioners, in direct sunlight or 

near other sources of heat. Failures can damage the TV or constitute a risk of fire. 
 
 
 

The installing should be carried out by at least two qualified people. The falling of the TV or 

its improper installing can cause damage and injuries. 
 
 
 

Recommended mounting surfaces: wooden beams, concrete and solid walls. If the install-

ing is carried out on other surfaces, please use special mounting brackets from the local ironware 
trades. 

 
 
Safety Information 

-

 

Before mounting the TV, this manual guide should be carefully read and fully understood  

-

 

The mounting has to be carried out by two qualified people. 

-

 

Do not use defective parts! 

-

 

Only suitable for stone, concrete walls, solid wood and wooden beams. By wood do not use 
rawl plugs. The wood has to be at least 5 mm pre-drilled. 

-

 

The wall has to carry the weight of the TV. 

-

 

If you are uncertain about the wall quality, consult a specialist! The manual guide does not 
replace special training. 

 
 
 
 
 
 

Summary of Contents for VM-SL10D






Reviews: