background image

 

© by WilTec Wildanger Technik GmbH 

 

Item 92453

 

Page 10 

 

http://www.WilTec.de

 

http://www.aoyue.eu  

 

  

 

07 2022

-1

 

http://www.teichtip.de

 

 

Set the throttle lever in proper position to ensure the engine runs at the required velocity.

 

 
 

Oil deficiency switch/alarm

 

 

The oil deficiency switch reacts to an insufficient quantity of motor oil in the crankcase. Lacking motor 
oil may damage the motor. As soon as the oil level in the crankcase is too low, the motor oil alarm stops 
the engine automatically to protect it from damages during operation.

 

 

Attention! 

Should you not be able to restart the motor, first check the oil level before checking any other 

possible cause of defect.

 

 
 

Motor protection switch

 

 

The protection switch that protects the charging circuit of the battery switches off automatically if there 
is  a  short  circuit  or  if  the  battery  poles  are  connected  improperly.  The  green  indicator,  jumping  out, 
interrupts the circuit. Re-set the indicator to its initial position after you have resolved the error that has 
triggered the indicator.

 

 
 

Stop/emergency stop

 

 

If there is an 

emergency,

 stop the motor by putting the engine switch to the “OFF” position. – To stop 

the engine in 

normal operation,

 proceed as follows:

 

1.

 

Put the throttle lever to “SLOW” position slowly (Fig.

 

16).

 

2.

 

Put the engine switch to the “OFF” position (Fig.

 

17).

 

3.

 

Put the fuel cock to the “OFF” position (Fig.

 

18) (optional).

 

 

 

Throttle lever – Fig.

 

16

 

 

(1)

 Engine switch – Fig.

 

17

 

 

(1)

 Fuel cock – Fig.

 

18

 

 

Attention! 

Never stop the motor suddenly when it operated with the throttle fully opened. Motor dam-

ages might result.

 

 
 

Exhaust regulation system

 

 

To keep the exhaust as low as possible, follow the steps mentioned below.

 

 

Maintenance

 

 

Maintain the motor regularly and according to the maintenance schedule of this manual. The mainte-
nance schedule has been established on the basis of a normal operation and normal conditions. If using 
the motor under heavy conditions, with a lot of dust generated, with ongoing humidity, or with high tem-
peratures, you should maintain the motor more frequently.

 

 

Exchanging components

 

 

It is advisable to use spare parts produced by our establishment or with identical quality. Poor-quality 
parts might provoke an increase of exhaust.

 

Summary of Contents for 92671













Reviews: