background image

 

© by WilTec Wildanger Technik GmbH 

 

Item 62551

 

Page 12 

 

http://www.WilTec.de

 

http://www.aoyue.eu  

 

  

 

12 2021

-1

 

http://www.teichtip.de

 

 

Regulations for waste disposal

 

 
 

The Waste Electrical and Electronic Equipment Directive (WEEE Directive, 2012/19/EU) of the EU was 
implemented in the German law related to electrical and electronic equipment and appliances.

 

 

All WilTec electric devices that fall under the WEEE directive are labelled with the symbol of a crossed-
out wheeled rubbish bin. This symbol indicates that this electric device must not be disposed of with the 
domestic waste.

 

 

WilTec  Technik  GmbH  is  registered  with  the  German  registration  authority  EAR  (Stiftung  Elektro-
Altgeräte Register) under the WEEE-registration number DE45283704.

 

 

Disposal of used electrical and electronic devices (in-
tended for use in the countries of the European Union 
and  other  European  countries  with  a  separate  waste 
collection system for these devices).

 

The symbol on the packaging or the product itself indi-
cates that this product must not be treated as normal 
domestic waste but must be disposed of at a recycling 
collection station for electrical and electronic waste.

 

By disposing of this product correctly, you contribute to 
the protection of the environment and the health of your 
fellow people. Inappropriate disposal threatens the en-
vironment and health.

 

 

Material recycling helps to reduce the consumption of raw materials.

 

 

Additional information about the recycling of this product can be provided by your local commune, the 
municipal waste disposal facilities, or the store where you purchased the product.

 

 
 
 
 

Address:

 

WilTec Wildanger Technik GmbH

 

Königsbenden 12 / 28

 

52249 Eschweiler Germany

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Important Note:

 

 

Reproduction and any commercial use (of parts) of this operating manual, requires a written permission 
of WilTec Wildanger Technik GmbH.

 

Summary of Contents for 62551













Reviews: