WilTec 61900 Operation Manual Download Page 3

Introduction

Thank you for purchasing this quality product.

 To minimize the risk of injury we urge that our cli-

ents take some basic safety precautions when using this device. Please read the operation in-
structions carefully and make sure you have understood its content.

Keep these operation instructions safe.

Read the manual

Hearing protection

must be worn

Eye protection 

must be worn

Hand protection 

must be worn

Foot protection 

must be worn

Protective clothing

must be worn

To avoid malfunctions, damage and health impairments, please follow the general safety in-
structions for pneumatic tools below as well as the following instructions!

Follow safety and accident prevention regulations.

In addition to the instructions in this operating manual, the local safety and accident prevention regula-
tions must be observed.

Handing over operating instructions to third parties

Ensure that third parties do not use this product until they have received the necessary instructions.

The device is not intended for use by persons (including children) with impaired or limited
physical, sensory or mental abilities as well as persons with a lack of experience and/or real
knowledge,   unless   they   have   been   given  supervision  or   instruction  concerning   use   of   the
device by a person responsible for their safety. Children should be supervised to make sure
that they do not play with the device. Children must not use this device without supervision.

Always be observant and always pay attention to what you are doing. 

Do not use this device if you are tired, inattentive or under the influence of alcohol, drugs or medica-
tion. A moment of inattention when using the electric device can result in serious accidents and injur-
ies.

© by WilTec Wildanger Technik GmbH 

Item 61900

Page 3 

http://www.WilTec.de
http://www.aoyue.eu  

  

03 2021

-1

http://www.teichtip.de

Summary of Contents for 61900









Reviews: