WilTec 51545 Operation Manual Download Page 9

 

© by WilTec Wildanger Technik GmbH  

Item 51545

–51547 

Page 9

 

http://www.WilTec.de

 

http://www.aoyue.eu   

   

10 2021

-1

 

http://www.teichtip.de

 

 

Disposal regulations

 

 
 
EU  guidelines  regarding  the  disposal  of  scrap  electric  appliances  (WEEE,  2012/19/EU)  were  imple-
mented in the law related to electrical and electronic equipment and appliances. 
 
All  WilTec  electric  devices  that  fall  under  the  WEEE  regulations  are  labelled  with  the  crossed-out 
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the 
domestic waste. 
 
The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE-
registration number DE45283704. 
 
Disposal  of  used  electrical  and  electronic  appliances 
(intended for use in the countries of the European Un-
ion and other European countries with a separate col-
lection system for these appliances). 
The  logo  on  the  article  or  on  its  packaging  points  out 
that  this  article  must  not  be  treated  as  normal  house-
hold waste but must be disposed to a recycling collec-
tion point for electronic and electrical waste equipment. 
By contributing to the correct disposal of this article you 
protect  the  environment  and  the  health  of  your  fellow 
men. Environment and health are threatened by inap-
propriate disposal. 
 
Material recycling helps reduce the consumption of raw materials. 
 
Additional information on recycling this article can be provided by your local community, municipal waste 
disposal facilities or the store where you purchased the article. 
 
 
 
 

Address: 

WilTec Wildanger Technik GmbH 

Königsbenden 12 / 28 

D-52249 Eschweiler 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Important notice: 
 
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction 
manual require the written permission of WilTec Wildanger Technik GmbH. 

Summary of Contents for 51545










Reviews: