background image

Amplifier Kit

Amplifier Kit

Installation

Guide

stallatio

stallat

Warning: 

This manual contains 

important safety and operating information. 
Please read and follow the instructions 
in this manual. Failure to do so could be 
hazardous and result in damage to your 
amplifi er.

!

SIGNALBOOST™
Mobile Amplifi er Kit
with Phone Cradle 

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · ·  1
How it Works  · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·   2
Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · ·   3
Installing the Magnet-Mount · · · · · · · · · · · · · · · · · · · · · ·  4
Installing the SIGNALBOOST™ Amplifi er  · · · · · · · · · · ·  5
Installing the Cradle Plus  · · · · · · · · · · · · · · · · · · · · · · · ·  5
Attaching the Ultra-Slim Antenna  · · · · · · · · · · · · · · · · · ·  7
Powering Up the Amplifi er  · · · · · · · · · · · · · · · · · · · · · · ·  8 
Connecting the Earbud   · · · · · · · · · · · · · · · · · · · · · · · · ·  8
Warnings and Recommendations  · · · · · · · · · · · · · · · · ·  9 
About Wilson Electronics   · · · · · · · · · · · · · · · · · · · · · · ·  10
Amplifi er Specifi cations  · · · · · · · · · · · · · · · · · · Back Cover

Wilson

®

         Electronics, Inc.

Summary of Contents for 811214













Reviews: