Wilson Electronics 801213 Installation Manual Download Page 10

9

 

Understanding the Amplifi er Lights

 

The power light PWR will turn green 
when the amplifi er is successfully 
powered up.  When the 800 MHz or 
1900 MHz lights are lit green, the 
amplifi er is amplifying the outside 
signal. 

If one or both frequency lights turn 
red, oscillation is occurring and the 
amplifi er has powered down.  The 
outside antenna needs to be moved 
farther from the Cradle Plus.  Move the 
outside antenna on the roof of the car 
to the rear of the car, but at least 8­12 
inches from the rear or side windows. 
Remove power from the amplifi er 
and reinstall power ­ this resets the 
amplifi er. 

If the lights are now green, the 
oscillation has stopped and the 
amplifi er is working.  If the red light is 
still on, move the antenna farther away 
and repeat the process. 

Always use a magnet­mount, mirror­ 
mount or roof­mount antenna.  Do 
not use a glass­mount antenna, as 
oscillation may cause continuous shut­ 
down of the amplifi er. 

An amber light in either the 800 
MHz or 1900 MHz position indicates 
overload from the cell site.  The 
amplifi er has temporarily shut down 
and will automatically reset.

Summary of Contents for 801213













Reviews: