background image

17

460061

5 dB (nominal)

> 90 dB

12V 1 .8A

4 .8

4 .8

4 .8

4 .6

4 .5

PWO460061

4726A-460061

SMB-Jack

50 Ohms

698-716 MHz, 728-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz

700 MHz B12/17

25 .4

700 MHz B13

25 .6

800 MHz B5

25 .6

1700 MHz B4

26 .7

1900 MHz B2

26 .9

Model 
FCC 
IC 

Connectors
Antenna Impedance
Frequency

Noise Figure
Isolation
Power Requirements

Power output for single cell 

phone (Uplink) dBm
Power output for single cell 

phone (Downlink) dBm

Specifications

Drive Reach Cell Signal Booster

Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the 

hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster 

is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the 

Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 

1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing 

power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.

The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. 

This device complies with Part 15 of FCC rules. This device contains licence-exempt transmitter(s)/receiver(s that comply with Innovation, Science and Economic Development 

Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)) This device must accept any 

interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by weBoost could void the authority 

to operate this equipment.

Summary of Contents for 460061

























Reviews: