background image

36

WILO SE 09/2013

English

1. General

1.1   About this document

These installation and operating instructions are
an integral part of the product. They must be kept
readily available at the place where the product is
installed. Strict adherence to these instructions is
a  precondition  for  the  proper  use  and  correct
operation  of  the  product.  These  installation  and
operating  instructions  conform  to  the  relevant
version of the product and the underlying safety
standards valid at the time of going to print.

2. Safety

These operating instructions contain basic infor-
mation which must be adhered to during installa-
tion and operation. For this reason, these operat-
ing instructions must, without fail, be read by the
service  technician  and  the  responsible  operator
before  installation  and  commissioning.  It  is  not
only  the  general  safety  instructions  listed  under
the main point "safety" that must be adhered to
but also the special safety instructions with dan-
ger  symbols  included  under  the  following  main
points.

2.1  Indication of instructions in the operating

instructions

Symbols

General danger symbol.

Danger due to electrical voltage.

NOTE: ....

Signals:

DANGER! Actuely dangerous situation.

Non-observance results in death or the most

serious of injuries.
WARNING! The user can suffer (serious) injuries.

'Warning'  implies  that  (serious)  injury  to  per-

sons is probable if this information is disregard-

ed.
CAUTION! There is a risk of damaging the

pump/unit. 'Caution' implies that damage to

the product is likely if this information is disre-

garded.

NOTE: Useful information on handling the prod-
uct. It draws attention to possible problems.

2.2  Personnel qualifications

The installation personnel must have the appro-
priate qualifications for this work.

2.3  Danger in the event of non-observance of the

safety instructions

Non-observance of the safety instructions can
result in risk of injury to persons and damage to
pump/unit. Non-observance of the safety
instructions can result in the loss of any claims to
damages.

In detail, non-observance can, for example,
result in the following risks:

•  Failure of important pump/unit functions,
•  Failure of required maintenance and repair pro-

cedures

•  Danger to persons from electrical, mechanical

and bacteriological influences,

•  Property damage.

2.4  Safety instructions for the operator

The  existing  directives  for  accident  prevention
must be adhered to.
Danger from electrical current must be eliminat-
ed. Local directives or general directives [e.g. IEC,
VDE etc.] and local power supply companies must
be adhered to.

2.5  Safety instructions for inspection and installa-

tion work

The operator must ensure that all inspection and
installation work is carried out by authorised and
qualified personnel, who are sufficiently informed
from  their  own  detailed  study  of  the  operating
instructions.
Work to the pump/unit must only be carried out
when at a standstill.

2.6  Unauthorised modification and manufacture of

spare parts

Modifications to the pump/unit are only permissi-
ble  after  consultation  with  the  manufacturer.
Original spare parts and accessories authorised by
the manufacturer ensure safety. The use of other
parts  can  nullify  the  liability  from  the  results  of
their usage.

2.7  Inadequate use

The operating safety of the supplied pump/unit is
only  guaranteed  for  conventional  use  in  accor-
dance  with  Section  4  of  the  operating  instruc-
tions.  The  limit  values  must  on  no  account  fall
under  or  exceed  those  specified  in  the  cata-
logue/data sheet.

3. Transport and storage

3.1  Shipping

The pump is supplied ex works in a box or fixed to
a pallet with straps and is protected against dirt
and moisture.

3.2  Transport inspection

When delivered, check the pump immediately for
any transport damage. If a damage is discovered,
the necessary procedure involving the forwarding
agent must be taken within the specified period.

3.3  Storage

Before  installation,  the  pump  must  be  kept  in  a
dry  place,  frost-free  and  protected  from  any
mechanical damage.

Summary of Contents for Wilo-MVIE Series





































Reviews: