background image

 

 

 

EdgeGard

 Dock Gates 

WARRANTY 

 

Wildeck EdgeGard™ Dock Gates are warranted to be free of material defects 
and workmanship for a period of one (1) year.

  When properly anchored, 

EdgeGard™ Dock Gates are also warranted to meet the 200 lb. OSHA 1910.23 load 
force protection requirement. 
 
The warranty begins at time of shipment from Wildeck’s factory.  Labor to install, 
adjust, maintain or replace the warranted gate, or any component part, is not 
included. 
 
This warranty is valid only if the Wildeck EdgeGard™ Dock Gate has been installed 
in complete accordance with Wildeck’s Installation Instructions.  Improprieties 
including but not limited to abuse, negligence, or failure to install, maintain or adjust 
the equipment properly, will void the warranty. 
 
The warranty is also voided if unauthorized parts, hardware or equipment are 
installed, or modifications are made to the Wildeck EdgeGard™ Dock Gate without 
prior written authorization.  Wildeck reserves the right to change, at any time, the 
material, design or specifications of its products without obligation to subsequent 
purchases, or add improvements without making corresponding changes to products 
previously manufactured. 
 
WILDECK SHALL NOT IN ANY EVENT BE LIABLE FOR ANY DAMAGES, WHETHER 
BASED ON CONTRACT, WARRANTY, NEGLIGENCE, STRICT LIABILITY OR 
OTHERWISE, INCLUDING WITHOUT LIMITATION ANY CONSEQUENTIAL, 
INCIDENTAL OR SPECIAL DAMAGES, ARISING WITH RESPECT TO THE EQUIPMENT 
OR ITS FAILURE TO OPERATE, EVEN IF WILDECK HAS BEEN ADVISED OF THE 
POSSIBILITY THEREOF. 
 
WILDECK MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND, 
EXCEPT THAT OF TITLE, AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, 
INCLUDING WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE, ARE HEREBY EXPRESSLY DISCLAIMED. 

 
 

 

Order No._______________________________ 

 
 

 

P.O. Box 89  •  405 Commerce Street 

Waukesha, WI  USA  53186 

262-549-4000  •  800-325-6939 

FAX  262-549-3466  •  [email protected]   
www.wildeck.com 

©  Wildeck, Inc.  2011 

Printed in USA  •  WG-EFR-IN 1109 

Summary of Contents for EdgeGard













Reviews: