background image

Your Curtis ADS System is Factory Pre‑Set for Optimum Performance.

After connection to water and power; the rear toggle switch must be on. You will hear a beep sound, indicating power is available to the controller. 

The control displays   

    . Press ON/OFF button and the screen will display   

   . After three seconds,  

           is displayed. 

Water will fill the tank (approximately 2-3 minutes depending on water flow rate). When the proper level is reached 

              will appear on the screen. 

It takes approximately 20 minutes to reach setpoint temperature of 200°F.

Control will display   

   when temperature reaches the setpoint (200°F); unit is at brewing temperature.

THERMOPRO

WILBUR CURTIS

WILBUR CURTIS

WILBUR CURTIS

FILLING . . .

WILBUR CURTIS

HEATING . . .

WILBUR CURTIS

READY TO BREW

2

BREWING INSTRUCTIONS

1.  Brewer should be ON (Confirm at rear toggle switch, then press the ON/OFF button). Screen should read Ready-to-Brew. If connected to an 

InterLock grinder. Grinder should be on. 

2.  Place an empty ThermoPro server centered beneath the brewcone.

6.  Select and press desired 

brew button. Brewing will 

begin immediately.

5.  Transfer filled brewcone 

to the brew rails.

3.  Place a clean filter into 

the brewcone.

4.   Fill brewcone with the 

proper amount of ground 

coffee. If Interlocked, 

fill the brewcone at the 

grinder.

WARNING

 TO AVOID SCALDING, Do not remove brewcone while brew light is flashing.

Summary of Contents for ThermoPro Single













Reviews: