Installation instructions (translation from original)
wienet
IoT Gateway Starter kit
IOT SK 100-DIO8-3G-W
83.041.1011.0
Wieland Electric GmbH
Brennerstraße 10 – 14
96052 Bamberg
Phone +49 951 9324-0
Fax
+49 951 9324-198
Doc. #
BA001202
– 11/2020 (Rev. B)
wienet
IOT SK 100-DIO8-3G-W
EN
NOTE
Personnel which installs, programs, operates or maintains this device must have read and
understood these instructions.
WARNING
•
The personnel must be thoroughly familiar with all warnings, notes and procedures de-
scribed in these operating instructions.
•
Where necessary, safety precautions and safety devices must comply with the applicable
regulations.
•
Damaged products must neither be installed nor put into operation.
•
The unit must not be opened.
•
Do not insert any objects into the unit!
•
Keep away from fire and water!
1
Function description
The wienet IOT GW 100-DIO8-3G-W devices communicate with the
wienet
Cloud via UMTS
modem or Ethernet. The communication mechanism has a low data volume and can be in-
tegrated easily in existing network infrastructures.
The IoT gateway is designed for an installation on a grounded 35 mm DIN rail in dry rooms.
The power supply of the device must be a grounded circuit PELV (connection between func-
tional earth and ground). The power supply must be a limited power source according to
the EN60950-1 chap. 2.5 or must be provided with an anti-surge fuse of 2 A.
2
Functional elements and indicators (fig. 2)
Pin assignments and connections
Power supply (fig. 2, j)
FE
GND
VCC
Functional earth
Ground
24 VDC
COM (fig. 2, k)
Pin
1
2
3
4
5
6
7
8
RS232 COM_GND CTS
–
Tx
–
RTS
–
Rx
RS485 COM_GND
–
B (+/Z)
–
A (-/Y)
–
TERM_120 –
CAN (fig. 2, l)
Pin
1
2
3
4
Description
CAN_HIGH
TERM_120
CAN_LOW
CAN_GND
Digital I/Os
Signal
Description
Signal
Description
+
24 VDC
Q 0
Digital output 0
I 0
Digital input 0
Q 1
Digital output 1
I 1
Digital input 1
Q 2
Digital output 2
I 2
Digital input 2
Q 3
Digital output 3
I 3
Digital input 3
-
Ground
LEDs
Status LEDs (fig. 2, i)
LED
Description
PLC
PLC status
Portal
Portal status
GSM
Modem status
LED 4
Freely programmable
Power
Device is powered
Ethernet interface (ETH; fig. 2, f)
LED
Description
Green LED
Link indication
Yellow LED
Activity indication
Network status (fig. 2, d)
Module status (fig. 2, c)
LED state
Description
LED state
Description
Off
Offline or not active
Off
Not initialized
Green
Online (RUN)
Green
Normal operation
Green, 1 flash
Online (STOP)
Green, 1 flash
Diagnostic event(s)
Green, blinking Blink
Red
Exceptional error or
fatal event
Red
Fatal event
Red, 1 flash
Station name error
Alternating
Red/Green
Firmware update
Red, 2 flashes
IP address error
Red, 3 flashes
Configuration error
3
Access to the web interface for the IoT gateway
The IoT gateway
is configured via a web interface using a web browser. Open the following
URL in the browser and enter the login data:
Address: http://192.168.1.10
User name: admin
Password: wienet123
The web interface then opens. If the window does not open, please check the proxy settings
for the browser you are using. Please do not use a proxy!
3
Installation
Inserting the SIM card
NOTE
•
Never use the device in areas where the operation of wireless equipment is prohibited.
•
When choosing a place to install the antenna, ensure the compliance with radiation lim-
its (20 cm min. distance from persons or other antennas).
•
Adhere to the lightning protection standard VDE V 0185 when installing the antenna out-
side. The antenna and its connection cable have to comply with the E.M.C. lightning
zone concept.
•
The device must be deactivated while working with the antenna.
Before installing the IoT gateway on the DIN rail and turning it on, insert the SIM card at the
rear side of the device (see fig. 3).
Mounting on support rail (see fig. 4)
1.
Tilt the unit slightly backwards.
2.
Fit the unit over top hat rail.
3.
Push the unit downwards and against the rail for locking.
4.
Check that the unit is locked into position.
Connecting to power
Prepare a suitable power source and connect it to the
wienet
IoT gateway.
Connecting to network device via ethernet
Connect your device by standard UTP/STP cable with RJ45 connectors to the
wienet
IoT
gateway.
4
Load factory settings (reset)
1.
Disconnect the IoT gateway from the power supply.
2.
Press the reset button (fig. 2, g) with a pointed object (e.g. a paper clip) and keep it
pressed (until step 5).
3.
Connect the IoT gateway to the power supply.
4.
Wait until the IoT gateway confirms the reset by two short flashes of all LEDs.
5.
Release the reset button and wait until the IoT gateway finished the restart. Do not dis-
connect the device from the power supply during the restart.
5
Removal from DIN rail (fig. 5)
WARNING
Switch mains power off and disconnect your system from the supply network.
Push down the power supply, and tilt upwards.
6
Technical data
Power supply
Supply voltage
24 VDC (
±
15%)
Active current
<140 mA
Interfaces
SD card interface, fig. 2, h microSD card
USB interface, fig. 2, e
Micro USB (OTG Host & Slave)
Antenna interface, fig. 2, a SMA connector (female)
SIM card interface, fig. 3
Mini-SIM (2FF)
Connectors
Wiring
Screw: 3-/10-pin; Push-in: 4-/8-pin
Connector cross-section
3-/10-pin: 0.2…1.5 mm² (AWG 28 – AWG 14)
4-/8-pin: 0.2…1 mm² (AWG 28 – AWG 14)
Stripping length
3-/10-pin: 7 – 8 mm; 4-/8-pin: 7 mm
General data
Operating temperature
0…+55 °C
Storage temperature
-20…+60 °C
Dimensions
see dimensional drawing, fig. 1
Degree of protection
IP20
EMC emission / immunity IEC 61000-6-3 / IEC 61000-6-2
UMTS
Max. RF transmitted power:
E-GSM/GPRS 900: 33.5dBM; EDGE 900: 28 dBm
DCS/GPRS 1800: 30.5 dBm; EDGE 1800: 27 dBm
WCDMA FDD/HSPA I/VIII: 24 dBm
CE:
Hereby, Wieland Electric GmbH declares that the
wienet
IOT SK 100-DIO8-3G-W is in
compliance with the following European directives:
RED directive 2014/53/EU, RoHS directive 2011/65/EU.
The complete EU Declaration of Conformity is available with the respective part number
under e.g.
https://eshop.wieland-electric.com/products/83.041.1011.0
in the register
"Downloads".
7
Scope of delivery
•
1 GW 100-DIO8-3G-W
•
1 Installation instructions
•
1 label MAC address
•
1 LAN cable
•
1 microSD card
•
1 UMTS antenna
•
1 plug-in power supply 230 V + cable
•
1 electronic input simulator with
plug-in terminal (3-/-10 pin)
1
2
3
4
5
e
f
h
i
j
k
l
g
a
b
c
d
