WIA Iss A Operator'S Manual Download Page 22

20 

Operators Manual

Quality

 

 

Reliability

 

 

Performance

12  

Warranty Information

WIA Weldmatic MIG Equipment 
Gold Shield Warranty Statement

Effective 1st January 2012

Welding Industries of Australia (WIA) 
warrants to the original retail purchaser 
that the Weldmatic welding machine 
purchased (Product) will be free from defects 
in materials and workmanship for a period 
of 3 years from the date of purchase of 
the Product by the customer. If a defect in 
material or workmanship becomes evident 
during that period, Welding Industries of 
Australia will, at its option, either:

•  Repair the Product (or pay for the costs of 

repair of the Product); or

•  Replace the Product.

In the event of such a defect, the customer 
should return the Product to the original 
place of purchase, with proof of purchase, 
or contact Welding Industries of Australia on 
1300 300 884 to locate an authorised service 
agent.

Any handling and transportation costs 
(and other expenses) incurred in claiming 
under this warranty are not covered by this 
warranty and will not be borne by Welding 
Industries of Australia. Welding Industries 
of Australia will return the replacement 
product, if original found to be faulty, freight 
free to the customer.

This warranty covers the Weldmatic power 
source and wirefeeder only, and does not 
extend to the regulator, gun assembly or 
accessories included in the original purchase 
package.

The obligation of Welding Industries of 
Australia under this warranty is limited to the 

circumstances set out above and is subject to:

•  The customer being able to provide 

proof of purchase of the Product and the 
purchase price paid for the Product;

•  The relevant defect in materials or 

workmanship;

•  The Product not having been altered, 

tampered with or otherwise dealt with 
by any person in a manner other than 
as intended in respect of the relevant 
Product; and 

•  The Product not having been used or 

applied in a manner that is contrary to 
customary usage or application for the 
relevant Product or contrary to any stated 
instructions or specification of Welding 
Industries of Australia.

Our goods come with guarantees that 
cannot be excluded under the Australian 
Consumer Law. You are entitled to a 

replacement or refund for a major failure and 

for compensation for any other reasonably 
foreseeable loss or damage. You are also 
entitled to have the goods repaired or 
replaced if the goods fail to be of acceptable 
quality and the failure does not amount to 

a major failure. The benefits given by this 

warranty are in addition to other rights and 
remedies which may be available to the 
customer under any law in relation to goods 
and services to which this warranty relates. 

Warranty provided by: 
Welding Industries of Australia  
(ABN 63 004 235 063) 
A Division of ITW Australia Pty Ltd  
5 Allan Street, Melrose Park,  
South Australia, 5039

Ph: 1300 300 884 
Email: [email protected] 
Web: www.welding.com.au

Summary of Contents for Iss A

























Reviews: