Whittier Wood Furniture McKenzie 1375AFCAF Assembly Instructions Manual Download Page 2

1375AFGAC; 1375AFCAF McKenzie Bookcase 

King Storage Bed — Parts List 

1377AFGAC; 1377AFCAF Headboard Kit (x1)

Page 2 — 1375AFGAC_1375CAF — 06/10

Please identify the parts and check that quantities received match those on this list.

If you need to replace a part, refer to the following letter and model name.

Y — #8x7/8" LoProfile Screw

— Qty. 4 (inserted)

ZE — Door Stay

— Qty. 2 (attached)

ZG — Door Stay Support

— Qty. 2 (attached)

ZF — #6x5/8" Undercut

Screw — Qty. 8 (inserted)

ZA — Hinge

— Qty. 6 (installed)

ZC — Magnetic Catch

— Qty. 4 (installed)

ZJ — #6x5/8" Philtruss

Screw — Qty. 8 (inserted)

ZB — Magnetic Plate

— Qty. 4 (installed)

X — Power Strip

— Qty. 1 (installed)

ZI — #6x5/8" Flat Head

Screw — Qty. 36 (inserted)

ZD — #5x5/8" Flat Head

Screw — Qty. 8 (inserted)

ZH — #6 x 1-1/4" Black Pan

Head Screw — Qty. 6 (inserted)

ZN — #8 x 1-1/4" Pan Head

Screw — Qty. 17 (inserted)

E — #8 x 1-1/4" Black

Screw — Qty. 59 (inserted)

ZO — #8 x 2-1/4" Black

Screw — Qty. 6 (inserted)

ZP — #8 x 1" Black

Screw — Qty. 16 (inserted)

ZQ — Left Bracket

— Qty. 2 (attached)

ZR — Right Bracket

— Qty. 2 (attached)

A — Headboard Assembly

— Qty.1

R — Assembled Door

— Qty. 2 (attached)

S — False Bottom

— Qty. 4

YB — #8 x 5/8" Pan Head

Screw — Qty. 8 (inserted)

ZS — Wire Clip

Screw — Qty. 8 (attached)

ZT — Tack Glide

— Qty. 4 (attached)

ZZ — Corner Brace

— Qty. 2 (attached)

YA — Large Adjustable Glide

— Qty. 2 (installed)

Summary of Contents for McKenzie 1375AFCAF













Reviews: