background image

5

Before Setting Oven Controls

Arranging Oven Racks

ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL (PRIOR TO
OPERATING THE OVEN). Always use oven mitts when using the oven.

Removing & Replacing Oven Racks

To remove, pull the rack forward until it stops. Lift up front of rack and slide out. To replace, fit the rack onto the guides on
the oven walls. Tilt the front of the rack upward and slide the rack back into place.

Oven Vent Location

For models equipped with coiled surface elements, the oven vent is located under
the left rear surface element
 When the oven is on, warm air flows through the
left rear element. This venting is necessary for proper air circulation in the oven
and good baking results. DO NOT BLOCK THE OVEN VENT.

Setting Clock & Minute Timer (some models)

 

To Set the 3 Button Clock (some models)

When the range is first plugged in, or when the power supply to the
range has been interrupted, "12:00" will flash in the display window.
1.

Slide switch C (CLOCK/TIMER) to the CLOCK position.

2.

Push in and hold button A (HOUR) until the correct hour appears
in the display. (The numbers will only count forward.)

3.

Push in and hold button B (MINUTE) until the correct minutes
appear in the display.

To Set the 3 Button Minute Timer

1.

Slide switch C (CLOCK/TIMER) to the TIMER position, "0:59" (59 MINUTES) will appear in the display window. The timer
can be set for any amount of time from 1 minute to 1 hour and 59 minutes.

2.

• To set a time more than 59 minutes, push in and release button A (HOUR). The display will show the maximum 1 hour

and 59 minutes. The time can now be adjusted down by pushing in and holding button B (MINUTE) until the correct
time appears in the display window.

• To set a time less than 59 minutes, push in and hold button B (MINUTE) until the correct minutes appear in the display.

(The minute timer will automatically start when the button is released.)

3.

When the set time has passed, the control will display "0:00" and beep continuously. Slide switch C (CLOCK/TIMER)
to the CLOCK position to cancel the timer and return to the clock mode.

Note: The 3 button clock graphics shown vary by model.

Models with no Clock

If your model has no Clock or Minute Timer, clock settings are not required to operate your range. Please proceed to Setting
Surface & Oven Controls
 in this Use & Care Manual.

3, 4 or 5

2 or 3

1

1

Summary of Contents for 316257134 (0809)













Reviews: