2
9/32"
3 1/16"
9/16"
3 15/32"
9/32"
1 3/32"
4 15/16"
3 25/32"
9/16"
1 3/32"
2 1/8"
3/8"
7/32"
W
R
2-WIRE
HEATING
THERMOSTAT
TYPE 24A06 DUAL LEVEL TEMP
WHITE
BLACK
W/WHITE
STRIPE
RED
BIMETAL
HEATER #1
BIMETAL
HEATER #2
SWITCH #1
SWITCH #2
TRANSFORMER
HEATING
LOAD #1
R
E
D
B
L
A
C
K
B
L
U
E
BLACK W/RED STRIPE
RED W/BLACK STRIPE
L1
L2
LINE
L1
L2
LINE
HEATING
LOAD #2
The Dual-Level Temp relay may be mounted in any position
without affecting it's performance.
It can be connected using the 1/2" male conduit hub
It can be connected using the 1/2" male conduit hub
It can be connected using the 1/2" male conduit hub
It can be connected using the 1/2" male conduit hub
It can be connected using the 1/2" male conduit hub and
can be mounted to any standard junction box or wiring
compartment.
It can also be mounted using the two holes in the back of
It can also be mounted using the two holes in the back of
It can also be mounted using the two holes in the back of
It can also be mounted using the two holes in the back of
It can also be mounted using the two holes in the back of
the case.
the case.
the case.
the case.
the case. Location of the mounting holes may be simplified by
holding the control against the mounting surface and marking
the proper position for drilling the holes.
INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION
All wiring should be done in accordance with local and national electrical codes and ordinances.
If a wiring diagram is supplied with the heating equipment,
follow those instructions. If none is available, two diagrams are
presented which show different wiring methods for the Silent
Operator relay.
OPERATION
OPERATION
OPERATION
OPERATION
OPERATION
As the thermostat closes its contacts, bimetal heaters #1 and
#2 are energized. Approximately 45 seconds later, the warp-
ing action of these heaters closes line voltage switches #1 and
#2 to energize heating loads #1 and #2.
When the thermostat opens its contacts, bimetal heaters #1
and #2 cool for approximately 45 seconds before line voltage
switches #1 and #2 open to de-energize the heating loads.
WIRING AND OPERATION
WIRING AND OPERATION
WIRING AND OPERATION
WIRING AND OPERATION
WIRING AND OPERATION
Use thermostat with a .4A fixed heater,
or set adjustable heater in thermostat
at .4A.
2-Wire Thermostat (R & W)
Black w/White stripe and
White to terminal W. Red to
terminal R.
Power Input:
Black & Blue
Heat Load 1:
Red & L2
Heat Load 2:
Black w/Red stripe & L2
Connection Table
Connection Table
Connection Table
Connection Table
Connection Table
1/2" STD CONDUIT HUB
WIRING
WIRING
WIRING
WIRING
WIRING
Line Voltage
Line Voltage Field
Low Voltage
Low Voltage Field
Fig. 2. Using Two-wire Heating Thermostat to
Fig. 2. Using Two-wire Heating Thermostat to
Fig. 2. Using Two-wire Heating Thermostat to
Fig. 2. Using Two-wire Heating Thermostat to
Fig. 2. Using Two-wire Heating Thermostat to
Operate Two Separate Heating Loads
Operate Two Separate Heating Loads
Operate Two Separate Heating Loads
Operate Two Separate Heating Loads
Operate Two Separate Heating Loads
Fig. 1. Dimensions of Type 24A06 Dual Level Temp
Fig. 1. Dimensions of Type 24A06 Dual Level Temp
Fig. 1. Dimensions of Type 24A06 Dual Level Temp
Fig. 1. Dimensions of Type 24A06 Dual Level Temp
Fig. 1. Dimensions of Type 24A06 Dual Level Temp
NOTE
