White Outdoor 76G, Operator'S Manual, Page: 21 / 34

Side to Side
If the cutting deck appears to be mowing unevenly, a side to side
adjustment can be performed. Adjust if necessary as follows:
With the tractor parked on a firm, level surface, place the
deck lift lever in the top notch (highest position) and rotate
both blades so that they are perpendicular with the tractor.
Measure the distance from the outside of the left blade tip 5.
to the ground and the distance from the outside of the right
CMBEFUJQUPUIFHSPVOE#PUINFBTVSFNFOUTUBLFOTIPVME
CFFRVBM*GUIFZSFOPUQSPDFFEUPUIFOFYUTUFQ
-PPTFOCVUEP/05SFNPWFUIFIFYDBQTDSFXPOUIFMFGU
6.
deck hanger bracket. See Fig. 6-5.
#BMBODFUIFEFDLCZVTJOHBXSFODIUPUVSOUIFBEKVTUNFOU
gear (found immediately behind the hex cap screw just
loosened) clockwise/up or counterclockwise/down. The deck
is properly balanced when both blade tip measurements
taken earlier are equal.
Retighten the hex cap screw on the left deck hanger bracket 8.
when proper adjustment is achieved.
Seat Adjustment
Refer to the Set-Up and Assembly section of this manual for seat
adjustment instructions.
Parking Brake Adjustment
8"3/*/(
Never attempt to adjust the brakes
XIJMFUIFFOHJOFJTSVOOJOH"MXBZTEJTFOHBHF150
move shift lever into neutral position, stop engine
and remove key to prevent unintended starting.
If the tractor does not come to a complete stop when the brake
QFEBMJTDPNQMFUFMZEFQSFTTFEPSJGUIFUSBDUPSTSFBSXIFFMT
can roll with the parking brake applied, the brake is in need of
adjustment. See an authorized service dealer to have your brakes
properly adjusted.
*.1035"/5
After cleaning your deck with the Deck Wash
4ZTUFN™SFUVSOUPUIFPQFSBUPSTQPTJUJPOBOEFOHBHFUIF150
,FFQUIFDVUUJOHEFDLSVOOJOHGPSBNJOJNVNPGUXPNJOVUFT
allowing the underside of the cutting deck to thoroughly dry.
Adjustments
8"3/*/(
Never attempt to make any
adjustments while the engine is running, except
XIFSFTQFDJGJFEJOUIFPQFSBUPSTNBOVBM
Leveling the Deck
NOTE: $IFDLUIFUSBDUPSTUJSFQSFTTVSFCFGPSFQFSGPSNJOHBOZ
deck leveling adjustments. Refer to Tires in the Service section of
this manual for more information regarding tire pressure.
Front To Rear
The front of the cutting deck is supported by a stabilizer bar that
can be adjusted to level the deck from front to rear. The front of
the deck should be between ¼-inch and 3⁄8-inch lower than the
rear of the deck. Adjust if necessary as follows:
With the tractor parked on a firm, level surface, place the 1.
deck lift lever in the top notch (highest position) and rotate
the blade nearest the discharge chute so that it is parallel
with the tractor.
Measure the distance from the front of the blade tip to the 2.
ground and the rear of the blade tip to the ground. The
first measurement taken should be between ¼” and 3⁄8” less
than the second measurement. Determine the approximate
distance necessary for proper adjustment and proceed, if
necessary, to the next step.
Locate the nut (s) on the front side of the stabilizer bracket. 3.
4FF'JH
'PSVOJUTXJUIOVUT
After loosening the jam nut:
Tighten the lock nut to raise the front of the deck;
Loosen the lock nut to lower the front of the deck.
Retighten the jam nut loosened earlier when proper
adjustment is achieved.
'PSVOJUTXJUIOVU
Tighten the nut to raise the front of
the deck;
Loosen the nut to lower the front of the deck.
'JHVSF
'JHVSF
S
ECTION
6 — M
AINTENANCE
& A
DJUSTMENTS