background image

15

Illustrated 

Parts List

To order replacement 

parts, contact  

1-800-949-4483, 

or visit us online at 

www.whiteoutdoor.com

8

Ref.

Part No.

Description

1

747-1161A

Control Handle

2

736-0451

Saddle Washer

3

736-0524B

Blade Bell Support

4

710-1044

Hex Bolt

5

747-0710

Hinge Pin

6

749-1092A

Upper Handle

7

710-1205

Rope Guide

8

710-1174

Carriage Bolt

9

749-0928A

Lower Handle

10

720-0279

Wing Nut

11

720-04072

Star Knob

12

714-0104

Hairpin Clip

13

746-0946

Control Cable 48.25”

14

726-0240

Cable Tie

15

17098

Hinge Clip

16

731-04019

Trail Shield

17

682-0139

20” Cutting Deck Assembly

18

742-0740

20” Mulching Blade

19

720-0426

Height Adjustment Knob

20

732-0404

Spring Lever

21

734-2004A

Wheel Assembly

22

736-0504

Wave Washer

23

731-04859

Snap-On Bail Cover

Ref.

Part No.

Description

24

731-0981A

Hubcap: Radial Spoke Gray

25

738-0507B

Shoulder Bolt

26

687-02077A Pivot Arm Assembly - RH Front

Pivot Arm Assembly - LH Rear

687-02076A Pivot Arm Assembly - LH Front

Pivot Arm Assembly - RH Rear

27

687-02179

Handle Bracket Assembly RH

687-02180

Handle Bracket Assembly LH

28

748-04096

Blade Adapter

753-0588

Blade Adapter Kit (for service)

29

732-0731

Torsion Spring

30

687-02075A Height Adjust. Assembly LH
687-02074A Height Adjust. Assembly RH*

31

782-7006

Mounting Bracket

32

736-0270

Bell Washer

33

710-0599

Hex Washer Hd. TT Screw

34

710-0654A

TT Sems Screw

35

731-1409B

Chute Deflector

36

682-7002

Mulching Plug Assembly

37

712-04065

Hex Lock Nut

38

787-01290

Height Adjustment Plate

39

782-5012

Rear Baffle 10.62 X 2.66

40

17033A

Front Baffle 10.62 RAD X 3.03

NOTE:

 For painted parts, please refer to the list of 

color codes below. Please add the applicable color 
code, wherever needed, to the part number to order 
a replacement part. For instance, if a part numbered 
700-xxxx is painted Red, the part number to order 
would be 700-xxxx-0650.
 
 

 

Metallic Red: 0650

 

 

Powder Black: 0637

Summary of Contents for 105

















Reviews: