White Mountain Hearth DVD32FP3 Series Page 10 Installation Instructions And Owner'S Manual Download

Page: 10 / 52

Page 10

17333-15-0806

Note: Discard insulation

& retainer when using

vertical venting off

VERTICAL VENTING

HORIZONTAL VENTING

FLUE INSULATION

INSULATION

RETAINER

INLET VENT COLLAR

FLUE OUTLET

COLLAR

FLUE COVER PLATE

(See note above)

INLET VENT

COVER PLATE

FLUE COVER PLATE

INLET VENT

COVER PLATE

Note: It is recommended that the

flue cover plate tab be pulled

outward prior to removal.

This will ensure that the plate

is not accidentally dropped

inside the rear air chamber.

Note: Discard insulation

& retainer when venting off

top of fireplace.

REAR VENT CONVERSION

Converting ﬂue take-off to rear venting

When switching out the ﬂue and inlet vent collars to run horizontally

off the rear vent, the following steps must be taken.
1. Remove the inlet vent collar (8 screws) and ﬂue collar (4 screws)

from the top of the ﬁreplace, and set to the side.

2. Remove the inlet cover plate and ﬂue cover plate located on the

back of the ﬁreplace. These will be used to close the top ﬂue

and inlet openings.

3. Insert the insulation retainer bracket and insulation into the top

ﬂue pipe before reinstalling the ﬂue cover plate over the top ﬂue

with 4 screws.

4. Reinstall the inlet cover plate over the top inlet opening with 4

screws. See illustration above..

5. Install the ﬂue collar assembly to the rear ﬂue with 4 screws.

6. Install the inlet vent collar to the rear of the ﬁreplace with 8

screws.

7. This completes the conversion for a rear vent application.

Note: for top vented installations, the insulation and retainer are

to be removed from the ﬂue pipe and discarded.

SPECIAL VENT SYSTEMS

The following vent systems are acceptable for use with the

DVD (32, 36, 42, 48)series ﬁreplaces:

Simpson Duravent® GS 4" - 6 ⅝", refer to page 23

*American Metal Products 4" - 6 ⅝"

*Selkirk Direct-Temp® 4" - 6 ⅝"

*Security Secure Vent® 4" - 6 ⅝"

Empire Horizontal Round Termination Kit DVVK-4RE,

refer to Page 27

Empire Flexvent Kit DVVK-4F, refer to page 30

* Can not be used in side wall horizontal vent

installations in the State of Massachusetts.

Summary of Contents for DVD32FP3 Series





















































Search results

Summary of Contents for DVD32FP3 Series

Reviews:

Related manuals for DVD32FP3 Series

Brands by name

Popular brands

White Mountain Hearth DVD32FP3 Series, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for DVD32FP3 Series

Reviews:

Related manuals for DVD32FP3 Series

Brands by name

Popular brands