background image

Engaging/Disengaging VG-2 

To engage VG-2:

• Press and hold the “Quiet” button until the 

“V

V//L

L” is illuminated.

To disengage VG-2:

• Press and hold the “Quiet” button until the 

“V

V//L

L” turns off.

VG-2 Detection

When a VG-2 signal is detected, the VG-2 alert is
sounded for 3 seconds and the display flashes
the “V

V//L

L” icon for 30 seconds.This cycle is

repeated if the VG-2 signal is again detected. 
During the period a VG-2 signal is detected, a
radar signal cannot be detected. However,
because the VG-2 alert has confirmed that a
patrol car is nearby, you are already aware of the
potential for speed monitoring and can adjust
your speed accordingly. Laser detection is not
affected while a VG-2 signal is detected.

VG-2 Audio/Visual Alerts

Note: 

You must turn this feature on before it will

detect VG-2.

When a VG-2 signal is detected, the detector ‘hides’ its
own radiated signal and becomes undetectable by
the VG-2.
Every 30 seconds, the detector checks for a VG-2
signal. If a VG-2 signal is still present, the unit
continues to hide and repeats the VG-2 alert. If no
signal is detected, two beeps are provided, 
indicating an “all clear” condition. During a VG-2
Alert X, K, and Ka band signals cannot be
received (Reference page 21 for VG-2 information).

OPERATION

OPERATION

Stay Alert Feature

The Stay Alert Feature is designed to test a dri-
ver’s alertness. To engage (when unit is not alarm-
ing):
• Press and hold City until a first audible alert is 

given. The “H

H” or “C

C” will flash indicating Stay

Alert is activated.                 

Within 30-60 seconds two beeps are sounded;
to show alertness, the driver must press either
the “City”, “Volume”, or “Quiet” buttons within 
3-5 seconds. If a button is pressed within 3-5 sec-
onds, the cycle is repeated.
If a button is not pressed within 3-5 seconds an
alarm sounds and displays multiple scrolling icons   
• Press Power to cancel Stay Alert.

WARNING!!!

Stay Alert is NOT intended as a

substitute for adequate rest. You should NOT oper-

ate a vehicle if you are drowsy. During extended

periods of vehicle operation, you should take fre-

quent breaks. Improper reliance on the Stay Alert

feature may result in vehicle damage, personal

injury or death.

NEVER OPERATE A VEHICLE IF

YOU ARE DROWSY

.

SWS

Safety Warning System

In communities where Safety Warning System™
transmitters are located, the detector will
receive over 60 messages. When Safety Radar is
detected, the audio alert is given and the dis-
play alternately flashes the “I”, “III” and “II”
icons.

Note: 

Not all areas have Safety Warning System

transmitters.

OPERATION

11

12

13

Auto Shut Off Mode

Auto Shut Off Mode automatically shuts off the
detector if you forget. 
The timer is reset:
1

1.. Each time the detector is turned off
2

2.. The optional power cord is unplugged
3

3.. Any button is pressed before the timer has 

expired.

The detector will alert you with an audible and
visual warning before it shuts off. This auto off
function can be programmed for the following:
Off, 1, 2, or 3 hours.
During this warning you can reset the timer by
pressing any button. 
If the unit has automatically turned itself off, press
the Power button to turn the unit back on. You can
manually engage the Auto Shut Off Mode by
pressing and holding the City button until one
beep is heard.
The Auto Shut Off feature can be disabled or
changed to 1 hour, 2 hours, or 3 hours. Press
and hold the “Quiet” button for approximately
2 seconds until a single beep is heard. The dis-
play will flash the “H

H” or “C

C” and the signal

strength indicators “II”, “IIII” or “IIIIII”, representing
hours. Pressing the “Volume” button will change
the selection. When no signal strength icons are
flashing, the feature is disabled.

Summary of Contents for XTR-180










Reviews: