manualshive.com logo in svg

Whisper Tech WhisperGen 3000 Series, Installation And Commissioning Manual

Share
Download
Whisper Tech WhisperGen 3000 Series Installation And Commissioning Manual Download Page 45

 

 

 

 

 

WhisperGen PPS16 Installation and Commissioning Manual Rev: 080801 

30

 

16.  Monitoring the WhisperGen using a 

computer. 

 

This option provides monitoring of the WhisperGen by a personal computer and “Micromon MO” 
software which shall be used to aid commissioning of the WhisperGen.  
 
See 

Figure 11

: Micromon MO screen. 

 
The Micromon MO software allows:  
 

•

 

all variables in the 

Extra Info Menu 

to be viewed on screen at the same time, instead of one 

at a time on the control panel. 

 

•

 

the recording of a log file detailing the readings of the WhisperGen sensors.  This is useful for 

fault solving. 

 
 Micromon MO software will run on a personal computer which is a minimum of an IBM 386 or 

compatible. 

 
 To install the Micromon MO software follow the instructions in the “DoReadMe.txt” file on the 

supplied disk.  Instructions for connecting the computer to the WhisperGen are in this file. 

 

 

Figure 10: Micromon MO screen 

 

 

Summary of Contents for WhisperGen 3000 Series






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands