manualshive.com logo in svg

Whirlpool WRS315SDHM, Owner'S Manual

Share
Download
Whirlpool WRS315SDHM Owner'S Manual Download Page 4

4

3.

Replace the burned-out light bulb, as explained in the
following sections.

4.

Reinstall the light shield, as explained in the following
sections.

5.

Plug in refrigerator or reconnect power.

Refrigerator Compartment – Upper Lights

Light Shield Removal:

Slide the light shield toward the rear of the refrigerator and remove
it from the light housing.

Replacement Bulb:

�

If the burned-out light is a full-size LED bulb, replace it with a
2.0 W LED bulb.

�

If the burned-out light is an incandescent bulb, replace it with
an incandescent appliance bulb of the same size, shape, and
wattage (40 W maximum).

Light Shield Reinstallation:

Align the light shield in the grooves at the bottom edge of the light
housing; then slide it forward until it snaps into place.

Refrigerator Compartment

–

Lower Lights

Light Shield Removal:

Slide the light shield to the right to remove the left end from the
wall slots; then pull the right end out of its wall slots.

Replacement Bulb:

�

If the burned-out light is a full-size LED bulb, replace it with a
3.6 W LED bulb.

�

If the burned-out light is an incandescent bulb, replace it with
an incandescent appliance bulb of the same size, shape, and
wattage (40 W maximum).

Light Shield Reinstallation:

Place the right end of the light shield into the wall slots; then snap
the left end into its wall slots.

Freezer Compartment

–

Upper Light

Light Shield Removal:

Gently squeeze the front and the bottom-rear edge of the light
shield to release the tabs from the wall slots; then pull the light
shield forward.

Replacement Bulb:

�

If the burned-out light is a full-size LED bulb, replace it with a
3.6 W LED bulb.

�

If the burned-out light is an incandescent bulb, replace it with
an incandescent appliance bulb of the same size, shape, and
wattage (40 W maximum).

Light Shield Reinstallation:

Align the light shield in its proper position, and snap the tabs into
the wall slots.

Freezer Compartment

–

Lower Light

Light Shield Removal:

Slide the light shield to the left to remove the right end from the
wall slots; then pull the left end out of its wall slots.

Replacement Bulb:

�

If the burned-out light is a full-size LED bulb, replace it with a
3.6 W LED bulb.

�

If the burned-out light is an incandescent bulb, replace it with
an incandescent appliance bulb of the same size, shape, and
wattage (40 W maximum).

Summary of Contents for WRS315SDHM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands