background image

4

INSTALLATION INSTRUCTIONS

Prepare Built-In Microwave/Oven 

Combination

NOTES: 

 

Refer to the following “Installation Instructions” and 

the “Installation Instructions” section of the Installation 

Instructions provided with your built-in microwave/oven 

combination.

 

Refer and adhere to the “Electrical Requirements” section 

and complete the instructions in the “Make Electrical 

Connection” section of the Installation Instructions 

provided with your built-in microwave/oven combination.

1. 

Decide on the final location for the oven. Avoid drilling or 

cutting into house wiring during installation.

2. 

To avoid floor damage, set the oven onto cardboard prior 

to installation. Do not use handle or any portion of the front 

frame for lifting.

3. 

Remove the shipping materials and tape from the oven. 

Remember to keep the corner posts and other materials 

that may be needed for installation.

4. 

Remove the hardware package from inside the bag 

containing literature.

5. 

Move oven and cardboard close to the oven’s final location.

Remove Oven Door

IMPORTANT:

 Use two hands to remove oven door(s).

1. 

Prior to removing the oven door, prepare a surface where 

you will place it. This surface should be flat and covered with 

a soft blanket, or use the corner posts from your packaging 

material.

2. 

Open the oven door.

3. 

Locate the oven door hinge locks in both corners of the oven 

door, and rotate the hinge locks toward the oven door to the 

unlocked position. If the door hinge lock is not rotated fully 

(see illustration B), the door will not remove properly.

4. 

Partially close the door to engage the door latch locks. The 

door will stop at this point.

5. 

Using two hands, grasp the edges of the oven door. Lift and 

pull the oven door toward you and remove. You may need to 

gently shift door from side to side as you pull.

6. 

Set the oven door(s) aside on the prepared covered work 

surface, with the oven door resting on its handle.

7. 

To continue with the oven installation, go to the “Positioning 

Oven Feet” section.

WARNING

Excessive Weight Hazard

Use two or more people to move and install oven.
Failure to do so can result in back or other injury.

B.  Oven door hinge lock in 

partially unlocked position

Locked 

position

Grip here 

to rotate.

Unlocked 

position

Soft close hinge 

arm on select models

A  Oven door hinge lock 

in locked position

Summary of Contents for WOC54EC0HB

















Reviews: