manualshive.com logo in svg

Whirlpool WhiteMagic LSE805, Service Manual

Share
Download
Whirlpool WhiteMagic LSE805 Service Manual Download Page 57

Installation of LSE805-60 Hz

1.

Ensure all the 4 feets touch the floor evenly and corners are level with each other.

2.

Donot place the machine on Slanting / uneven / unstable surface.

3.

Place on a solid levelled surface to avoid excessive vibration during operation.         

4.

Keep the machine at least 10cm away from the wall on all sides.

5.

Ensure the assembly of rat mesh at the time of installation.

6.

Ensure Suspension bracket is removed from the machine before operation.

7.

Ensure Inlet fill hose is connected to the Tap through tap adopter.

8.

Place the drainhose flat on the floor before operating the machine.

9.

Ensure the earth connection in your Electrical supply is proper before the 
connecting the power cord. The socket should be standard and independent of 2 
pin type of 220V/60 Hz.

10.

Do not use extension junction box since it may not be properly earthed.

Summary of Contents for WhiteMagic LSE805





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands