background image

11

Check Operation of Oven Broil Burner

1. Close the oven door.

2. Press the BROIL pad.

3. Press the START pad.

The oven burner should light within 8 seconds. Under certain 
conditions it may take the burner up to 50 to 60 seconds to light. 

Refer to the Use and Care Guide for proper operation of the oven 
controls.

Adjust Oven Broil Burner Flame (if needed)

Look through oven window to check broil burner for proper 
flame. This flame should have a ½" (1.3 cm) long inner cone of 
bluish-green, with an outer mantle of dark blue, and should be 
clean and soft in character. No yellow tips, blowing or lifting of 
flame should be present.

If flame needs to be adjusted:

1. Loosen the lock screw on the air shutter located at the rear of 

the broil burner.

2. Adjust the air shutter as needed. 

3. Tighten lock screw.

4. Press CANCEL/OFF when finished.

Warming Drawer

(on some models)

Remove all items from inside the warming drawer, and allow the 
range to cool completely before attempting to remove the drawer.

To Remove:

1. Open drawer to its fully open position.

2. Locate the black triangle-shaped tabs on both sides of the 

drawer.

3. Press the tab down on the right side, and lift tab up on the left 

side at the same time, then pull drawer out another inch.

4. Holding the drawer by its sides, slowly pull it all the way out.

To Replace:

1. Align the drawer glides with the receiving guides.

2. Push drawer in all the way.

3. Gently open and close the drawer to ensure it is seated 

properly on the slides.

Storage Drawer

(on some models)

The storage drawer can be removed. Before removing, check 
that the storage drawer is cool and empty. A flat-blade 
screwdriver will be needed for removal.

To Remove:

1. Pull the storage drawer forward to the drawer stop. Push the 

drawer back approximately 1" (2.5 cm).

It will be necessary to disengage the storage drawer one side 
at a time.

2. Insert a flat-blade screwdriver through the opening in the side 

of the storage drawer, placing the screwdriver tip on the 
outside of the drawer clip.

A. Lock screw
B. Air shutter

A. Tab

A

B

A

A. Drawer clip

A

Summary of Contents for WFG371LVQ





















Reviews: