background image

INSTALLATION INSTRUCTIONS

30" (76 CM) FREESTANDING ELECTRIC RANGES

Table of Contents

RANGE SAFETY ..................................................................................2

INSTALLATION REQUIREMENTS.....................................................3

Tools and Parts .................................................................................3
Location Requirements.....................................................................3
Electrical Requirements - U.S.A. Only..............................................5

INSTALLATION INSTRUCTIONS.......................................................6

Unpack Range ..................................................................................6
Install Anti-Tip Bracket......................................................................6
Electrical Connection - U.S.A. Only..................................................8
Verify Anti-Tip Bracket Is Installed and Engaged...........................12
Level Range ....................................................................................13
Warming Drawer or Premium Storage Drawer...............................13
Storage Drawer ...............................................................................14
Oven Door .......................................................................................14
Complete Installation ......................................................................14
Moving the Range...........................................................................15

IMPORTANT:

 

Save for local electrical inspector's use.

W10403811C

Summary of Contents for WFC340S0AB

















Reviews: