Whirlpool R-106 Training Manual Download Page 27

Page: 27 / 34

Low Ice Production

•

Step 1: Check Freezer temperature

(optimal 0°F, ±3°F)

– Adjust Freezer temperature as needed

• L

ower Temp for More Ice

Note: The average temperature of the

Iceland ice maker compartment is 15

degrees F. (The set point of the ice

maker compartment is 25 degrees if the

icemaker switch is turned "off").

Step 1:

Check Freezer temperature (optimal 0°F, ±3°F)

Adjust Freezer temperature as needed
Lower Temp for More Ice

Note:

The average temperature of the Iceland ice maker compartment is 15 degrees

F. (The set point of the ice maker compartment is 25 degrees if the icemaker switch

is turned “off”).

•

Step 2: Check size and quality of cubes

– If undersized, check and diagnose water supply

• P

lugged screen on water valve?

• F

rozen or partially plugged fill tube?

• W

ater pressure too low?

• Refrigerator hooked up to Reverse Osmosis filter

• Water supply hooked up to Self-Piercing water

valve?

Is enough water being supplied to the icemaker?

Small or undersized cubes are usually an indication that there’s not enough water

entering the icemaker. Cubes should all be about the same size (between 2⅜ and 2⅝

in length).

Summary of Contents for R-106



































Search results

Summary of Contents for R-106

Reviews:

Related manuals for R-106

Brands by name

Popular brands

Whirlpool R-106, Training Manual

Search results

Summary of Contents for R-106

Reviews:

Related manuals for R-106

Brands by name

Popular brands